Page
3
MT04-001 AquariTherm Tap (Manual)
www.dartvalley.co.uk
Re
vi
si
on N
o. M
AQ
TI
N
16
07
13
01
Page
2
MT04-001 AquariTherm Tap (Manual)
www.dartvalley.co.uk
Re
vi
si
on N
o. M
AQ
TI
N
16
07
13
01
The control box should be located in a dry location and not
exposed to dirt, dust or damp. The unit should be accessible when
required, but not within easy reach of unauthorised persons.
It will be necessary to make adjustments and service the control
box after installation, and in the future. Secure access areas and
duct spaces are recommended.
The control box is not designed for direct surface mounting into
washroom areas. Never open the cover with the supply live.
The routes that cables will take when connecting external
equipment to the control box should also be planned at this stage.
The shower control system is typically used with a high security
shower head.
Important: Thermostatic mixing valve
It is recommended that hot water is supplied through an approved
TMV3 thermostatic mixing valve to prevent scalding (sold
seperately).
Step 3 :
Typical installation
Step 2 :
Kit Contents
Step 1 :
Safety First
These instructions relate to the use of the Shower Control System
only, any external or ‘add-on’ parts will be supplied with separate
instructions.
It is recommended that the electrical part of the installation be
carried out by a qualified electrician in accordance with the latest
electrical regulations. It is also recommended that any plumbing
is carried out by a qualified plumber.
*Not to scale
IMPORTANT :
Please read these instructions carefully
and follow each stage in order!
IMPORTANT :
It is recommended that hot water is supplied
through an approved TMV3 thermostatic mixing valve (sold
seperately), in order to prevent scalding.
Step 5 :
Fixing & wiring
Step 4 :
Board layout
Input connection - Sensor 1
Output connection - Valve 1
Input connection - Sensor 2
Output connection - Valve 2
Cable entry - Sensor 1
Cable entry - Valve 1
Cable entry - Sensor 2
Cable entry - Valve 2
Mains supply
Time setting switches
Option switches
LED 1 - For engineers / testing only
LED 2 - For engineers / testing only
LED 3 - For engineers / testing only
Fuse (replace with exact same type)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
9
15
12
10 11
14
13
4
3
8
7
6
5
2
1
DO NOT extend cables
DO NOT leave badly fitted cables
DO NOT interfere with the mains flex
DO check all cables and connections
DO ask for advice if / when necessary
The box should be securely fixed in a suitable location in a
horizontal orientation, so that the front label is read correctly.
Remove lid to expose four fixing locations around the edge of the
enclosure (see Fig. 3). These areas allow the fastening of the unit
without removing the printed circuit board.
Drill through these marked areas away from the wall to avoid dust
entering the control box, then hold control box in position against
the wall and mark holes with a pencil. Remove box, drill and plug
marked areas and fix the control unit with suitable fixings.
Connect the mains supply lead to a 230V ac supply via a fused
spur, the fuse rating should be 3 Amps. The mains supply should
NOT be initiated until all external equipment has been installed
and wired.
Always read instructions supplied with external components and
ensure that only the supplied equipment is connected to the
control box.
Cables should enter the enclosure through the cable glands. Keep
all connections tidy and do not allow cable to finish or hang in the
transformer area. .
It is recommended that each cable is fed through the relative
cable gland into the enclosure; the cable can then be pulled out
towards the fitter to allow the connector plugs to be fitted.
The connector plugs can be disconnected from the mating
sockets when wiring external equipment, double check positions
with the plug orientations as they only fit one way!
When each plug has been wired the cables can be pulled back
through the cable glands, and the plug re-connected to the
corresponding socket. Cables should not be left to torte or slack.
When all connections are made and checked, replace the lid and
secure.
Fixing locations
Fuse
Connector plug
Fixing screw
Sensor (x1 or x2)
Solenoid valve (x1 or x2)
Control box
0870 122 8822
Sensor
Control box
Shower head
Mixed water
TMV mixing valve
Solenoid valve
Hot
Cold
Your kit will include the following parts*:
