Armitage Shanks A4125AA Скачать руководство пользователя страница 6

Страница: 6 / 20

Ø35

Ø20

114

INSTALLATION GUIDE

DO NOT

apply heat near this product. Heat generated by soldering

could damage plastic parts and seals.

5.1 Mounting

Before connection, flush water through pipe-work to remove

all debris etc. to prevent damage to the valve mechanism.

THEN ENSURE WATER SUPPLIES HAVE BEEN ISOLATED.

Mark the profile of the spout onto the

panel at the preferred location & drill

two holes as shown. Upper hole is for

the fixing stud & inlet pipe, lower hole

is for the cables.Ensure the

holes remain within the area

sealed by the foam gasket

(pre-fitted to rear of spout).

Fit the rubber moulding to the metal fixing plate.

Then from behind the panel slide the fixing plate as

sembly onto the fixing stud as shown.

Hand tighten the nut against the fixing plate until the

rubber moulding makes contact with the rear of the

panel. Ensure the spout is positioned correctly, & then

tighten the nut securely with a 13mm A/F spanner.

Screw the copper inlet pipe into the spout, trim to

length if necessary. Ensure the foam gasket is in place

as shown. This gasket should already be fitted into the

recess at the rear of the spout (self adhesive).

The M8 fixing stud should also be pre-fitted.

Offer the spout towards the holes in the panel.

Feed the inlet pipe, fixing stud & cables through

panel holes. Push the spout against the panel &

ensure the foam gasket makes contact

CABLE COLOURS:

The cables emerging from the spout are connected to the integral sensor.

BLACK & RED cables will connect to the solenoid valve.

GREY cable will connect onto the PCB inside the PSU

Do not cut these cables

INSTALLATION HEIGHT: we recommend the spout outlet be positioned

approximately 150-200mm above the basin or worktop (which ever is

higher). Greater height may cause users to splash water outside the ba-

sin whereas lower height may affect activity space. Consideration should

also be give to the overall aesthetical appearance. Installations vary

significantly, so use this dimension as a guideline only.

DRILL PANEL

HOLES Ø35 & Ø20

www.divapor.com

Содержание A4125AA





















Результаты поиска

Содержание A4125AA

Отзывы:

Бренды по названию

Популярные бренды

Armitage Shanks A4125AA, Руководство по установке

Результаты поиска

Содержание A4125AA

Отзывы:

Бренды по названию

Популярные бренды