ARM Musca-S1 Скачать руководство пользователя страница 118

Страница: 118 / 194

Table 3-59 INTR_STATUS Register bit assignments

Bits

Name

Function

[31:3]

Reserved.

[2:0]

INTR_STATUS[2:0]

Indicates the reference counter interrupt
status:

0b0

: No interrupt.

0b1

: Interrupt:

Reset value

0b0

CLEARED_STATUS Register

The CLEARED_STATUS Register characteristics are:

Purpose

Stores the cleared statuses of the sensors.

Usage constraints

This register is read-only.

Memory offset and full register reset value

See

3.9.1 PVT sensor control registers summary

on page 3-113

The following table shows the CLEARED_STATUS Register bit assignments.

Table 3-60 CLEARED_STATUS Register bit assignments

Bits

Name

Function

[31:3]

Reserved.

[2:0]

CLEARED_STATUS[2:0]

Stores the cleared statuses of the sensors:

0b0

: Not cleared.

0b1

: Cleared.

Reset value

0x000

SAMPLED_STATUS Register

The SAMPLED_STATUS Register characteristics are:

Purpose

Individually indicates that PVT measurements are valid.

Usage constraints

This register is read-only.

Memory offset and full register reset value

See

3.9.1 PVT sensor control registers summary

on page 3-113

The following table shows the SAMPLED_STATUS Register bit assignments.

3 Programmers model

3.9 PVT sensor registers

101835_0000_01_en

reserved.

3-118

Non-Confidential

Содержание Musca-S1


































































































































































































Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды

ARM Musca-S1, Техническое справочное руководство

Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды