ARM DSTREAM-XT Скачать руководство пользователя страница 26

Страница: 26 / 38

DSTREAM-XT Getting Started Guide

Document ID: 102443_1.0_00_en

Version 1.0

Set up your DSTREAM-XT system

3.2 Install the USB drivers for the DSTREAM-XT system

on Linux

To use the DSTREAM-XT system with a USB connection, for your operating system, install the USB

device drivers provided with Arm

Development Studio 2021.1 or later.

Before you begin

Ensure you have:
• Installed Arm Development Studio. For more information, see the

Arm Development Studio

Getting Started Guide

• Administrative privileges on your host computer.

About this task

The drivers for the DSTREAM-XT system are optionally installed as part of the installation process

for Arm Development Studio. If you have skipped the driver install process in Arm Development

Studio, follow these steps to install them.

Procedure

1. Using root privileges, run the

run_post_install_for_Arm_Development_Studio_vx.x.sh

script ﬁle that is

available in the Arm Development Studio install directory. The

x.x

in the ﬁlename denotes the

Arm Development Studio version that is installed on your host computer.

2. To conﬁrm the installation, enter

yes

Results

The USB drivers are now installed on your host computer.

Related information

Connect and power up the DSTREAM-XT system

on page 26

3.3 Connect and power up the DSTREAM-XT system

Describes how to connect your DSTREAM-XT system to your host computer and target hardware.

Before you begin

• You must

install Arm Development Studio

to access the software drivers and debug hardware

conﬁguration utilities.

• Your target hardware must have a debug or PCIe connector supported by DSTREAM-XT. For

a list of supported connectors, see

Target interface connectors

in the Arm

DSTREAM-XT

System and Interface Design Reference Guide.

Non-Conﬁdential

Page

Содержание DSTREAM-XT






































Результаты поиска

Содержание DSTREAM-XT

Отзывы:

Похожие инструкции для DSTREAM-XT

Бренды по названию

Популярные бренды

ARM DSTREAM-XT, Руководство по началу работы

Результаты поиска

Содержание DSTREAM-XT

Отзывы:

Похожие инструкции для DSTREAM-XT

Бренды по названию

Популярные бренды