Code Selection
The push button unit generates random code sequences to which the chime unit is
able to learn. Should your door chime unit activate intermittently for no apparent
reason, the uncontrolled activation may be caused by another unit nearby or from a
device operating on the same frequency.
Code/Push Button Limiting Switch
Your door chime unit is capable of working with
a maximum of 4 Push Button units at 4 different
frequency channels. If your door chime unit
activate intermittently for no apparent reason,
it might caused by a nearby device working
on a similar frequency channel. To eliminate
frequency channel interruption, Code/Bell
Push Button Limiting Switch is to limit the Push
Button unit and/or frequency channel that your
door chime unit can be activated by.
1. Insert batteries into the Door Chime unit
and press the Push Button unit once, the
door chime will sound to indicate that 1st
operating code is registered and memorized.
This is the factory setting and intended to
limit the activate frequency channel and Bell
Push Button unit to 1.
2. To register 2nd Bell Push Button operating code and/or frequency channel, Press
and hold the code setting switch on the door chime unit for 1 second, it will give a
“Beep” sound to indicate that door chime is ready to learn the 2nd operating code,
press the 2nd Push Button unit once, the door chime will sound to indicate that 2nd
operating code is registered and memorized. This will allow 2 different Push Button
units and/or frequency channels working with the door chime at the same time.
3. Repeat the same procedure for the 3rd and 4th Push Button units. The maximum
amount of Push Button units and frequency channels that the door chime unit can
be work at the same time are 4.
4. To reset Code/Bell Push Button limiting function, remove batteries from the door
chime for at least 10 seconds, and reinsert the batteries, this will reset the door
chime unit to learn 1 Push Button unit and frequency channel only.
NOTE: low battery in doo chime or push button unit will erase or rest the registered
frequency channel between the door chime and push button unit, if the door chime
unit does not sound when push button unit depressed, please replace batteries on
door chime and push button unit, then set up both units again.
Resetting the Unit
To avoid uncontrolled activation:
1. Switch off the Chime Unit for at least 1 minute.
2. Switch back on. A double beep should be heard indicating that the unit is in
learning mode.
3. Press the Push Button. The chime should sound to indicate code selection.
4
3
2
WARNING
This product contains a Lithium Coin type battery.
WARNING! Please ensure the coin battery is kept OUT OF REACH OF CHILDREN.
The battery presents a significant choking and burn hazard to young children
should they swallow a battery. Under 4 year-olds are especially prone to
accidental swallowing of objects such as these.
If a lithium coin battery is swallowed, SEEK IMMEDIATE MEDICAL ATTENTION.
Do not let the child eat or drink; Do not induce vomiting.
To keep your children safe:
• Keep devices that use coin batteries out of reach of small children
• Keep new batteries in their packaging until ready to use and store
in places out of reach of children
• Safely dispose of spent batteries immediately
• Share this information with your family, friends, caregivers and babysitters.
We have designed the coin battery holder to require dexterity normally beyond that
of a small child to access, but nevertheless you should always follow the advice
given above.
Push Button
1. Push Button unit is operated by 1 x 3 volt Lithium battery (CR2032 - included).
2. Remove the back of case by pushing in the tab on the bottom with a small, flat
screwdriver.
3. The 3 volt Lithium battery (CR2032) is already installed.
Simply pull off the isolation strip which will allow the battery to make electrical contact.
NOTE: When the push button unit is depressed, an orange LED light will lit on, but this
is not an indicator of the push button unit battery level. It is recommended to replace
batteries once a year to ensure range and transmission reliability.
To Replace the Battery
Remove the locking screw from the battery holder clip and remove old
battery. Insert 1 x 3 volt Lithium battery (type CR2032) in the battery
compartment, ensuring the battery polarity is correct as in Figure 1.
Replace clip and tighten locking screw to hold battery firmly in place.
Chime Unit
Remove battery cover from the rear of the door chime unit by sliding it
towards the bottom edge of the unit.
Insert 2X AA size batteries, alkaline type batteries are recommended, do not use
rechargeable batteries; do not mix old and new batteries or different types. Ensure
batteries are connected at the correct polarity.
Replace the battery cover once batteries are inserted.
When the chime unit is power up, it will emitted a double beep sound, press
the push button unit immediately to register the connection between chime and
push button unit.
Installation
Do not mount the chime and push button unit near metal objects, UPVC frame, heat/
radio source, security door or in close proximity to any radio emitting equipment.
The range of the unit may be substantially reduced
.
Push Button Unit
The Push Button unit has two mounting holes on rear plate of unit that must be
pushed through before unit can be mounted.
1. Remove rear plate of unit (see battery installation).
2. Push through tabs in mounting holes.
3. Using the back plate of the Push Button unit as a guide, mark the position
of holes onto mounting surface.
4. Drill appropriately sized holes and insert wall plugs if required.
5. Secure the back plate of Push Button unit to mounting unit.
6. Clip Push Button unit to back plate.
Alternatively the Push Button unit can be attached to smooth mounting surfaces such
as painted wood, glass and plastic using Self-Adhesive Pad (supplied).
Do not mount the push button unit on metal or near metal door frame, security door,
metal furniture or in close proximity to any radio emitting equipment.
The range of the unit may be substantially reduced.
Door Chime Operation
Once the Push Button and Chime units have been installed in their desired locations,
the system is ready for use.
Depress button on Push Button unit momentarily, and chime should sound. Press button
again to repeat. Continual pressing of the button will not repeat the chime. If chime
fails to sound, check batteries in push button and check power is on to Chime Unit.
Tone Selection
The Wireless Door Chime is supplied with 8 built-in chimes.
Westminster Chime
Twinkle Twinkle
Double Ding-Dong
It’s a Small World
Circus Theme
Dog Barking
Banjo on My Knee
Telephone Ring
To change the chime tune, remove the Push Button Unit’s rear cover.
Inside the Push Button Unit locate the small Tune Selector push button marked ‘S’
(Ref. Figure 1). Each time that this Tune Selector push button is pressed, the next of
the 8 melodies will be played. You can step through and listen to each in turn. When
you hear the melody you wish to choose, do not press the tune selector again. The
chime will play the selected melody each time the bell press is pushed. At any time
you can select another melody by repeating the tune selector button process.
Refit the Push Button Unit rear cover.
Whenever the Push Button Unit battery is fitted or replaced, the chime tune may
default to the Westminster Chime.
Fig 1.
S
CPIN002726
Code/Bell Push
Button Limiting
Switch