Ariston XC 902 GH DC AUS, Инструкция по использованию и установке

Страница: 6 / 16

5 AUS
HOW TO KEEP YOUR OVEN IN SHAPE
Important: The appliance should be disconnected from
the mains supply before starting cleaning operations.
To ensure a long life cycle for the appliance, it is essential
to carry out a thorough general clean frequently, while
observing the following instructions:
Inside the oven door:
Clean the surface with a cloth moistened with hot water
and non abrasive liquid detergent, then rinse and dry
thoroughly.
Inside the oven:
• The inside of your oven is coated with a special self-
cleaning microporous enamel glaze which, at a normal
cooking temperature of between 200 and 300°C, oxidises
and completely eliminates all grease spots or other
substances that inevitably attack the inner walls of the
oven. This way, cleaning is kept right down to a minimum:
as a matter of fact, you just need to rub the surfaces of
the oven with a wet cloth regularly, after cooking, to
remove the thin layer of ash that may have been
deposited during cooking, in order to maintain the self-
cleaning property of the oven intact.
• After cooking where liquid has overflowed or when the
dirt has not been eliminated completely (for example
when grilling food, and the temperatures reached are
not high enough for the full self-cleaning action of the
enamel to be performed), we recommend you leave the
oven on at maximum temperature so that all grease
residue and the like are eliminated.
• If, after long-term use, you find evident grease stains
deposited on the self-cleaning oven walls, probably due
to your failing to follow the above maintenance advice,
clean the surfaces thoroughly with hot water and a soft
cloth (do not use any detergents), then rinse and dry
thoroughly.
• Do not remove any dry caked-on grease using sharp
objects, as these could etch the self-cleaning coating.
• If the self-cleaning surfaces inside the oven are damaged
or worn, due to incorrect or poor maintenance or after
many years of use, you can request a kit of self-cleaning
panels to line the inside of the oven. To order these, just
contact an authorised Service Centre.
Before cleaning your oven, or performing maintenance,
disconnect it from the power supply.
To extend the life of your oven, it must be cleaned frequently,
keeping in mind that:
•
The self-cleaning panels (if present) and the enameled
parts should be washed with warm water - abrasive
powders and corrosive substances should be avoided;
• The inside of the oven should be cleaned immediately
after use with warm water and soap; the soap should
be rinsed away and the interior dried thoroughly;
• Stainless steel can be stained if it remains in contact
with agressive detergents (containing phosphorus) or
water with a high lime content. We recommend that you
rinse these parts thoroughly and dry them well after
cleaning. It is also a good idea to dry any water spills;
fig 3
fig 4
• Never line the bottom of the oven with aluminium foil
because the buildup of heat will not only impede the
cooking process, but could also damage the enamel.
Replacing the Lamp in the Oven
•
Cutoff the supply of power to the oven by turning off the
omni-polar switch connecting it to the mains, or by
removing the plug if it is accessible;
• Unscrew the glass cover attached to the lamp holder;
• Unscrew the lamp and replace it with another high-tem-
perature lamp (300°C) with the
following characteristics:
- Voltage: 230/240 V
- Wattage: 15W
- Socket: E14
• Remount the glass cover and
reconnect the appliance to the
power supply.
Protective kit
During operation, the oven glass door and adjacent parts
of the appliance become hot. Make sure, therefore, that
children do not touch the appliance.
Disassembling/assembling the oven door
To make it easier to clean the inside of your oven, the oven
door can be removed, by proceeding as follows (fig. 1-2):
• Open the door completely and lift the 2 levers “B” (fig. 1);
• Now, shutting the door slightly, you can lift it out by pulling
out the hooks “A” as shown in figure 2.
To reassemble the door:
• With the door in a vertical position, insert the two
hooks “A” into the slots;
• Ensure that seat “D” is hooked perfectly onto the edge
of the slot (move the oven door backwards and forward
slightly);
• Keep the oven door open fully, unhook the 2 levers “B”
downwards and then shut the door again.
Greasing the taps
As time passes, a tap may lock or become difficult to turn.
In this case it will be necessary to clean inside and replace
the grease. This procedure must be performed by a
technician authorized by the manufacturer.