12
GB
The Controls
!
Warning,
after pressing the
START/PAUSE
button
,
the programme cannot be changed. To change a selected
programme, press the
START/PAUSE
button
the light
flashes Amber to indicate the programme is paused. Select
the new programme and any options required, the light will
then flash green. Press the
START/PAUSE
button
again
and the new programme will start.
•
Option buttons
These buttons serves to personalise the selected
programme according to personal requirements.
Not all options are available for all programmes.
Some options are incompatible with the ones
previously set. If the button of any unavailable option
is pressed, the buzzer will beep 3 times. If the option
is available, the option light will stay on.
Progress (
Drying,
Cool Tumble) icons
These are part of the Display, they indicate the progress of
the dryer. Each icon comes on as the corresponding phase
starts.
Delay Timer (Time Delay)
The start of some programmes
(see The Display and
Programmes tables)
can be delayed for up to 24 hours.
Crease Care
The
pre-care option
is only available if a delayed start has
been selected. It tumbles the clothes occasionally during
the delayed period to help prevent creases developing. The
post-care option
occasionally tumbles the clothes after end
of the drying and cool tumble cycles to prevent creases
developing, should you not be available to remove the load
immediately the programme is complete
Note:
The
START/PAUSE
light flashes Amber during
this phase. Selecting this option enables both the pre and
post care functions if appropriate.
Heat Level button and lights
Not all programmes allow you to change the heat level and
some programmes allow all three heat level options:
Low, Medium and High.
When the heat level options are available pressing this
button changes the heat level and the light corresponding to
the selection is lit.
Sound
If selected, gives a signal at the end of the drying cycle, to
remind you that the clothes are ready to be removed.
Not available with the Heat & Enjoy programme.
• DISPLAY
“8:88”
The display shows either the amount of time delay remaining or
an indication of the amount of time left for a drying programme
(see The Display)
.
The colons between the hours and minutes
in the display flash to show that the time is counting down.
When the programme finishes its cool tumble phase the display
will show ‘End’.
• Door
Opening
Opening the door (or pressing the Start/Pause Button) during a
programme will stop the dryer and have the following effects:
• The START/PAUSE light flashes Amber.
• During a delay phase the delay will continue to count
down. The START/PAUSE button must be pressed to
resume the delay programme.
• The START/PAUSE button must be pressed to resume
the programme. The progress lights will change to show
the current status and the Start/Pause light will stop
flashing and turn green.
• Changing the Programmes knob will select a new
programme and the START/PAUSE Light will flash
green. You can use this to select the “Refresh”
programme to cool the clothes if you find them dry
enough. Pressing the START/PAUSE button to begin
new Programme.
• Note
If you have a power cut, switch off the power or remove the
plug. When power is restored, plug in the machine, press and
hold the ON/OFF button until the dryer reactivates, then press
Start/Pause button.
Drying times
The drying time depends on the size of the load and on the type of fabric it contains
(see Table).
The COOL TUMBLE cycle runs during the final 10 minutes of the programme.
!
For large loads, select the High Heat option if available.
Fabric
Load
1 kg
2 kg
3 kg
4 kg
5 kg
6 kg
7 kg
Cotton –
high heat
20 - 30
minutes
35 - 45
minutes
45 - 60
minutes
60 - 70
minutes
70 - 80
minutes
80 - 100
minutes
90 - 120
minutes
Synthetics –
higt heat
20 - 30
minutes
35 - 45
minutes
45 - 60
minutes
-
-
-
Acrylics –
low heat
25 - 40
minutes
40 - 60
minutes
-
-
-
-
