EN
15
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.
*
Only available in selected models.
Problem:
Possible causes / Solutions:
The dishwasher does not start or cannot
be controlled.
• Switch off the appliance by pressing the ON/OFF button, switch it back
o n a f t e r a p p r o x i m a t e l y o n e m i n u t e a n d r e s e t t h e c y c l e .
• The appliance has not been plugged in properly.
• The dishwasher door has not been shut properly.
The door won’t close.
• The lock was released. Strongly push the door until a “clacking” noise
i s h e a r d .
N o w a t e r d r a i n s f r o m t h e
d i s h w a s h e r.
• The dishwasher cycle has not yet finished.
• The water inlet hose is bent (
s e e I n s t a l l a t i o n ) .
• The drain duct is blocked.
• The filter is clogged up with food residues.
T h e d i s h w a s h e r m a k e s e x c e s s i v e
n o i s e .
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not
b e e n m e a s u r e d o u t c o r r e c t l y o r i t i s n o t s u i t a b l e f o r u s e i n d i s h w a s h e r s
( s e e S t a r t - u p a n d u s e ) .
T h e d i s h e s a n d g l a s s e s a r e
c o v e r e d i n a w h i t e f i l m o r
l i m e s c a l e d e p o s i t s .
• The level of refined salt is low or the dosage setting is not suited to the
h a r d n e s s o f t h e w a t e r ( s e e R i n s e a i d a n d s a l t ) .
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
T h e d i s h e s a n d g l a s s e s a r e
s t r e a k e d o r h a v e a b l u i s h t i n g e .
• The rinse aid dosage is too high.
T h e c r o c k e r y h a s n o t b e e n d r i e d
p r o p e r l y.
• A wash cycle without a drying cycle has been selected.
• The rinse aid has been used up or the dosage is too low (
s e e R i n s e a i d
a n d s a l t ) .
• The rinse aid dispenser setting is not suitable.
• The crockery is made from non-stick material or plastic.
T h e d i s h e s a r e n o t c l e a n .
• The racks are overloaded (
s e e L o a d i n g t h e r a c k s ) .
• The crockery has not been arranged properly.
• The sprayer arms cannot rotate freely.
• The wash cycle is too gentle (
s e e Wa s h c y c l e s ) .
• An excessive amount of foam has been produced: the detergent has not
b e e n m e a s u r e d o u t c o r r e c t l y o r i t i s n o t s u i t a b l e f o r u s e i n d i s h w a s h e r s
( s e e S t a r t - U p a n d U s e ) .
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (
s e e C a r e a n d m a i n t e n a n c e ) .
• The refined salt level is low (
s e e R i n s e a i d a n d s a l t ) .
• Switch off the appliance by pressing the ON/OFF button. Shut off the
w a t e r t a p t o e l i m i n a t e t h e r i s k o f f l o o d i n g a n d r e m o v e t h e p l u g f r o m t h e
e l e c t r i c a l s o c k e t .
M a k e s u r e t h e w a t e r i n l e t f i l t e r h a s n o t b e c o m e b l o c k e d b y i m p u r i t i e s
(see “Care and maintenance” chapter).
T h e d i s h w a s h e r d o e s n o t t a k e a n y
w a t e r i n - Ta p s h u t - o f f a l a r m
(indicator light ON/OFF flashing;
H2O and
tap
symbol displayed;
F 6 appears after a
few seconds).
• There is no water in the mains supply.
• The water inlet hose is bent (see
I n s t a l l a t i o n ) .
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken
w h e n t h e b e e p s s o u n d e d .
Switch off the appliance using the ON/OFF button, turn on the tap and
s w i t c h t h e a p p l i a n c e b a c k o n a f t e r a f e w s e c o n d s b y p r e s s i n g t h e s a m e
b u t t o n . R e - p r o g r a m t h e a p p l i a n c e a n d r e s t a r t t h e w a s h c y c l e .
Clogged filter alarm
The “
filter
” symbol on the display will light
up.
• Make sure the wash cycle has ended, open the dishwasher door
and clean the cup filter and stainless-steel filter (see “Care and
maintenance” chapter). The “blocked filter” symbol will go off when the
f o l l o w i n g c y c l e s t a r t s .
