manualshive.com logo in svg

Arista 7000 Series, Быстрый старт

Поделиться
Скачать
Arista 7000 Series Скачать руководство пользователя страница 16

 

Bracket Mount Examples for Two-Post Rack Mount displays proper bracket mount configuration
examples. Improper Bracket Mount Examples for Two-Post Rack Mount displays improper bracket
mount configuration examples.

Figure 3: Bracket Mount Examples for Two-Post Rack Mount

Figure 4: Improper Bracket Mount Examples for Two-Post Rack Mount

3.1.1

 Attaching Mounting Brackets to the Chassis

This procedure attaches mounting brackets to the switch chassis

1. Align the mounting brackets with the attachment pins to obtain the desired mounting position.
2. Place the bracket flush on the chassis with attachment pins protruding through key-openings.
3. Slide the bracket toward the front flange until the bracket clip locks with an audible click.

Figure 5: Attaching the Mounting Brackets to the Switch Chassis

To remove the mounting bracket from the chassis, lift the front edge of the mounting bracket clip
with a flathead screwdriver and slide the bracket away from the front flange (opposite from the
installation direction).

3.1.2

 Inserting the Switch into the Rack

This procedure attaches the switch to the rack.

12

Содержание 7000 Series























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды