background image

GB - 24

TROUBLESHOOTING

PROBLEM

PROBABLE CAUSE

CORRECTION

Engine will 

not 

crank/start.

 1.

Safety interlock system is not 
engaged or is faulty.

 1.

Check safety interlock system 
(see Safety Interlock System on 
page 11).

  2.

Fuel tanks empty.

  2.

Fill fuel tanks (see FILLING FUEL 
TANKS
 on page 13).

 3.

Fuel shut-off valve closed.

 3.

Open fuel shut-off valve.

 4.

Discharged battery.

 4.

Charge battery (see Charging the 
Battery
 on page 21).

 5.

Poor connection between battery 
and battery cables.

  5.

Tighten battery cables and/or 
clean battery and battery cables 
(see Cleaning Battery and Battery 
Cables
 on page 21).

 6.

Spark plug wire(s) loose or spark 
plug(s) faulty.

 6.

Connect spark plug wire(s) or 
replace spark plug(s). Refer to 
Engine Manual for detailed 
instructions.

  7.

Faulty electrical system.

  7.

Contact your Ariens Dealer.

  8.

Faulty engine.

  8.

Contact your Ariens Dealer.

Engine

 runs 

rough.

 1.

Choke engaged.

 1.

Disengage choke.

 2.

Air filter cartridge plugged.

 2.

Clean or replace air filter 
cartridge. Refer to Engine Manual 
for detailed instructions.

  3.

Faulty engine.

  3.

Contact your Ariens Dealer.

Unit does 

not move 

with engine 

running 

when using 

steering 

levers.

  1.

The transmission bypass lever is 
engaged.

 1.

Disengage transmission bypass 
lever (see  on page 15).

  2.

Faulty hydrostatic belt.

  2.

Replace hydrostatic belt (see 
REPLACING HYDROSTATIC 
BELT
 on page 23).

  3.

Faulty transmission.

  3.

Contact your Ariens Dealer.

PTO or 

mower 

blades do 

not engage 

or shuts off.

  1.

Operator presence switch not 
depressed.

 1.

Depress operator presence switch 
by sitting on seat.

 2.

Faulty operator presence switch.

  2.

Contact your Ariens Dealer.

 3.

Electric clutch connector is loose 
or disconnected.

  3.

Connect the electric clutch 
connector. See REPLACING 
HYDROSTATIC BELT 
on 
page 23 f
or the electric clutch 
connector location.

 4.

Faulty PTO belt.

 4.

Replace PTO belt (see 
REPLACING PTO BELT on 
page 22).

 5.

Faulty PTO switch, wires, 
connectors, or clutch.

  5.

Contact your Ariens Dealer.

Engine 

overheats.

  1.

Engine oil level low.

  1.

Add engine oil. Refer to Engine 
Manual for detailed instructions.

 2.

Cooling system plugged.

 2.

Clean cooling system. Refer to 
Engine Manual for detailed 
instructions.

  3.

Faulty engine.

  3.

Contact your Ariens Dealer.

Содержание ZOOM 1540

































Отзывы: