background image

EN - 2

Read these safety rules and follow them 
closely. Failure to follow these rules could 
lead to loss of control of unit, severe personal 
injury or death to you or bystanders, or result 
in damage to property or the machine.

PRACTICES & LAWS

Practice usual and customary safe working 
precautions. Learn applicable rules and laws 
in your area. Always follow the practices set 
forth in this manual.

REQUIRED OPERATOR 
TRAINING

The original purchaser of this unit was 
instructed by the seller on safe and proper 
operation. If unit is to be used by someone 
other than the original purchaser, loaned, 
rented, or sold, ALWAYS provide this manual 
and any needed safety training before 
operation.

SAFETY ALERT SYMBOL

SIGNAL WORDS

The safety alert symbol above and signal 
words below are used on decals and in this 
manual. Read and understand all safety 
messages.

1. Danger

2. Warning

3. Caution

4. Notice

NOTICE: 

Indicates information or procedures 

that are considered important but not hazard 
related. If not followed, property damage 
could result.

5. Important

IMPORTANT: 

Indicates general reference 

information worthy of special attention.

SAFETY DECALS

The safety decals on your machine are visual 
reminders of the important safety information 
in this manual. All messages on your unit 
must be fully understood and carefully 
followed. Safety decals on the machine are 
explained below.

Always replace missing or damaged safety 
decals. Replacement decal information is in 
the parts manual for your machine. Decals 
can be ordered from your dealer. 

See Figure 2 for safety decal locations.

SAFETY

WARNING: 

AVOID INJURY. 

This snow thrower is capable of 
crushing or amputating body 
parts. Failure to observe the 
safety instructions in the 
manuals and on decals could 
result in serious injury or death.

ALWAYS disengage auger, stop 
unit and engine, remove key and 
allow moving parts to stop 
before leaving operator’s 
position.

This is the safety alert symbol. It 
means:

ATTENTION!

YOUR SAFETY IS 

INVOLVED!

When you see this symbol:

BECOME ALERT!

OBEY THE MESSAGE!

DANGER: 

Indicates an 

IMMINENTLY HAZARDOUS 
SITUATION! If not avoided, 
WILL RESULT in death or 
serious injury.

WARNING: 

Indicates a 

POTENTIALLY HAZARDOUS 
SITUATION! If not avoided, 
COULD RESULT in death or 
serious injury.

CAUTION: 

Indicates a 

POTENTIALLY HAZARDOUS 
SITUATION! If not avoided, MAY 
RESULT in minor or moderate 
injury. It may also be used to 
alert against unsafe practices.

Содержание Sno-Thro Pro 28 926038































Отзывы: