manualshive.com logo in svg

Ariens Pro 28 EFI CE, Руководство по обслуживанию, Страница: 34 / 84

Поделиться
Скачать
Ariens Pro 28 EFI CE Скачать руководство пользователя страница 34

EN – 33

Install Auger

See Figure 67.
1.

Install auger onto auger shaft with auger kickers facing 
gearcase.

IMPORTANT: 

Make sure auger helix direction matches 

original auger orientation.
2.

Apply grease to grease zerks and spin auger by hand 
to spread grease along auger shaft.

3.

Repeat step 2.

4.

Reinstall support bushing onto auger shaft end.

5.

Align holes in auger with holes in auger shaft and 
reinstall shear bolt. Torque bolt to 7.9 N•m – 16.5 N•m 
(5.8 lb-ft – 12.2 lb-ft). If torque wrench is unavailable, 
tighten until bolts no longer spin freely. DO NOT 
overtighten.

6.

Reinstall auger assembly into housing so impeller 
shaft is seated in ball bearing at housing rear. See 
Figure 68.

7.

Align holes in bushings on auger ends with holes in 
housing and partially thread all six tapping screws.

8.

Tighten tapping screws.

Figure 66

Figure 67

1. Auger Kicker
2. Grease Zerk

1

2

Figure 68

Содержание Pro 28 EFI CE





















































































Отзывы:

Нет отзывов