manualshive.com logo in svg

Ariens Pro 28 EFI CE, Руководство по обслуживанию, Страница: 17 / 84

Поделиться
Скачать
Ariens Pro 28 EFI CE Скачать руководство пользователя страница 17

EN – 16

7.

Remove hardware retaining bottom cover to frame 
and remove cover. See Figure 21.

Install Bottom Cover

1.

Reinstall bottom cover and secure with two tapping 
screws and four hex bolts.

2.

Models 926068, 926070, 926334, 926336, 926337:

 

advance to step 6.

Models 926060, 926069, 926338

See Figure 22.
3.

Reposition height adjuster stop against height adjuster 
bracket. Align slot with top hole in height adjuster 
bracket.

IMPORTANT: 

Align one of the three notches in height 

adjuster with lock finger to hold adjuster position.

4.

Reinstall carriage bolts through height adjuster 
bracket and reinstall spacers onto bolts.

5.

Reinstall height adjuster plate and secure with three 
flange nuts.

All Models

6.

Return unit to operating position.

Figure 21

CAUTION: 

AVOID INJURY. Height adjuster is 

unsecured until hardware is reinstalled. Be 
careful not to bump adjuster from position on 
lock finger. Keep hands away from pinch points.

Figure 22

Содержание Pro 28 EFI CE





















































































Отзывы:

Нет отзывов