manualshive.com logo in svg

Ariens Pro 28 EFI CE, Руководство по обслуживанию, Страница: 15 / 84

Поделиться
Скачать
Ariens Pro 28 EFI CE Скачать руководство пользователя страница 15

EN – 14

Generation 3 Chute Control Design

See Figure 16.
18. Remove hairpin from clevis pin and reinstall cable 

eyelet onto clevis pin.

19. Insert clevis pin through chute control bracket and 

secure with hairpin.

Generation 2 Chute Control Design

20. Remove hairpin from chute control assembly and 

reinstall cable eyelet onto assembly. Reinstall hairpin. 
See Figure 17.

All Models

21. Reinstall gear cover and secure with tapping screw.
22. Reinstall chute deflector cable into J-clamp on engine 

mount.

23. Reinstall deflector cable anchor into deflector bracket.

24. Remove sleeve bushing and hairpin from deflector 

arm and reinstall cable eyelet onto deflector arm. 
Reinstall sleeve bushing and hairpin. See Figure 6.

25. Reconnect spark plug wire.
26. Adjust chute lock cable and deflector cable. Refer to 

operator’s manual for instructions.

IMPORTANT: 

Check all adjustments after first use.

Figure 16

Generation 3 Chute 
Control Design

Figure 17

Generation 2 Chute Control Design

WARNING: 

AVOID INJURY. Auger / impeller 

must stop within 5 seconds when attachment 
clutch lever is released.

Содержание Pro 28 EFI CE





















































































Отзывы:

Нет отзывов