manualshive.com logo in svg

Ariens Pro 28 EFI CE, Руководство по обслуживанию, Страница: 13 / 84

Поделиться
Скачать
Ariens Pro 28 EFI CE Скачать руководство пользователя страница 13

EN – 12

See Figure 12.
22. Remove hardware securing auger housing to frame.
23. Lift auger housing rear slightly to disengage from 

mount rod and separate from unit.

Reinstall Auger Housing

See Figure 13.
1.

With help from an adult assistant, engage attachment 
clutch lever so attachment brake will not obstruct 
attachment drive pulley in step 2.

2.

Tilt auger housing rear up and lower into frame so 
housing mount brackets engage mount rod.

3.

Release attachment clutch lever.

4.

Align holes in housing mount brackets with holes in 
frame and reinstall two tapping screws, but DO NOT 
tighten.

IMPORTANT: 

Unit must be on a flat, level surface during 

steps 6 – 8.
5.

Check tire pressure and adjust if necessary. Refer to 
Operator’s Manual for specification.

6.

Loosen skid shoe hardware and adjust skid shoes. 
Refer to Operator’s Manual for adjustment procedure.

7.

Torque tapping screws installed in step 5 to 
33.8 N•m – 70.1 N•m (24.9 lb-ft – 51.7 lb-ft).

See Figure 14.

8.

Reinstall attachment drive belts onto attachment 
sheave.

Figure 12

1. Tapping Screw
2. Mount Rod

1

2

WARNING: 

AVOID INJURY. Attachment sheave 

edges are sharp. Wear thick gloves to install 
belts onto attachment sheave.

Figure 13

Содержание Pro 28 EFI CE





















































































Отзывы:

Нет отзывов