Ariens 926078 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 34

background image

EN - 26

SHORT TERM

1. Run auger / impeller for a few minutes to

remove loose or melting snow to prevent
impeller from freezing.

2. Tighten all hardware to correct

specifications.

3. Inspect unit for visible signs of wear or

damage. Repair as needed.

4. Apply a light layer of oil or anti-rust

compound on bare metal areas.

5. Prepare fuel system for storage.

NOTICE:

Ariens recommends using a quality

fuel stabilizer in all fuel. Gasoline left in the
fuel system without a stabilizer, even for short
periods of time, deteriorates and leaves
gummy deposits in the system that may
damage the carburetor and fuel hoses, filter
and tank. For the best effectiveness, add
stabilizer to all fuel containers whenever
purchasing fuel. Add the stabilizer to the
container before adding fuel.

a. Add Ariens fuel stabilizer (see

14) or equivalent

according to manufacturer's
instructions to the fuel tank and any
fuel containers with remaining fuel.

b. Run engine outdoors for at least

5

minutes to allow stabilizer to reach

the carburetor.

6. Close fuel valve and allow engine to stop

on its own.

7. Turn engine key to stop position and

remove key.

8. Store unit in a cool, dry, protected area.

Do not store unit outdoors.

LONG TERM

1. Perform all short-term storage items.
2. Wash salt and other corrosive ice-melting

agent residue from unit with mild soap
and low-pressure water.

IMPORTANT:

Never spray unit with high-

pressure water.
3. Lubricate as directed in

on

page 14.

4. Touch up all scratched painted surfaces.

5. Remove weight from wheels by putting

blocks under frame or axle.

6. Store unit in a cool, dry, protected area.

Do not store unit outdoors.

START-OF-SEASON FUEL

PREPARATION

Before opening the fuel valve for the first time
after long-term storage, add fresh, stabilizer-
treated fuel to the fuel tank and any fuel
containers with remaining fuel.

See your Ariens dealer for a complete list of
compatible accessories and attachments for
your unit.

STORAGE

WARNING:

AVOID INJURY.

Read and understand the

section before proceeding.

ACCESSORIES

Description

Part No.

Front Weight Kit

72406500

Composite Skid Shoe Kit

(Set of 2)

72603100

Cover

72601500

Snow Cab

72102600

36" Snow Brush Kit

82600300

Protective Floor Mat

70706700

«
...
26
27
28
29
30
...
»

Содержание 926078



































Отзывы:

Нет отзывов

Похожие инструкции для 926078

Бренд: XPower Страницы: 18

Бренд: Murray Страницы: 178

Бренд: Oleo-Mac Страницы: 32

Minute Mount 2 XV2 Series

Бренд: Fisher Страницы: 16

Бренд: SNOWJOE Страницы: 20

Бренд: Cub Cadet Страницы: 52

Бренд: White Outdoor Страницы: 22

Бренд: Tuthill Страницы: 34

Бренд: Cub Cadet Страницы: 16

Бренд: Nilfisk-Advance Страницы: 100

Бренд: Stanley Страницы: 20

Бренд: MTD Страницы: 20

Бренд: Unigreen Страницы: 40

HLG 650-2000 LCD

Бренд: Gude Страницы: 48

Бренд: Meec tools Страницы: 72

Sahara Pro TurboDryer X4

Бренд: Legend Brands Страницы: 6

Бренд: Sanitaire Страницы: 8

Бренд: Premier Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды