Ariens 916302 amp 24 sno-thro Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 38

background image

GB - 22

SHEAR BOLTS

IMPORTANT:

Use only Ariens shear bolts for

replacement. Use of any other type of shear
bolt may result in severe damage to unit and
may void the warranty.
Occasionally a foreign object may enter the
auger/impeller housing and jam the auger,
breaking the shear bolts which secure the
auger to the shaft (Figure 20). This allows the
auger to turn freely on the shaft which may
help prevent damage to gear case and its
components.

Replacement

1. Align shear bolt holes in auger with

shear bolt holes in the shaft.

2. Drive shear bolt through hole. If shear

bolt was broken this will drive remaining

part from shaft.

3. Secure shear bolt with nut.

REMOTE DISCHARGE

DEFLECTOR CONTROL

ADJUSTMENT

Figure 21
If discharge deflector does not follow full

range of travel:

1. Push deflector remote all the way

forward.

2. Loosen adjusting nuts on remote

deflector cable attached to the chute

deflector (Figure 21).

3. To adjust the deflector lower:

Loosen bottom adjustment nut and
tighten top adjustment nut.
To adjust deflector higher:
Loosen top adjustment nut and tighten
bottom adjustment nut.

4. Check the deflectors range of travel and

repeat adjustment as necessary.

DISCHARGE CHUTE

If discharge chute does not stay in position
while operating, tighten nut (2) at pivot point
to increase tension on spring. See Figure 22.

Figure 19

OS0482

1. Skid Shoe
2. Skid Shoe Hardware

Figure 20

1. Auger
2. Shear Bolts

OS2610

Figure 21

1. Adjusting Nuts
2. Cable Support Bracket
3. Remote Deflector Control Cable
4. Discharge Deflector

«
...
20
21
22
23
24
...
»

Содержание 916302 amp 24 sno-thro







































Отзывы:

Нет отзывов

Похожие инструкции для 916302 amp 24 sno-thro

Бренд: Jolog Страницы: 28

Бренд: Toro Страницы: 4

Бренд: ebm-papst Страницы: 12

Бренд: Shindaiwa Страницы: 40

Бренд: Kongskilde Страницы: 8

Бренд: Cub Cadet Страницы: 32

Бренд: Wolf Garten Страницы: 141

Бренд: Wolf Garten Страницы: 142

Бренд: Toro Страницы: 124

Бренд: Meec tools Страницы: 56

Бренд: Meec tools Страницы: 127

Vac Attack II ZR08107

Бренд: Homelite Страницы: 20

Vac Attack UT08084

Бренд: Homelite Страницы: 24

VAC ATTACK II UT08042

Бренд: Homelite Страницы: 22

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 6

Бренд: Snapper Страницы: 64

Бренд: Ventrac Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды