Ariens 911707 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 36

Ariens 911707 Скачать руководство пользователя страница 19

GB - 19

Wheel Drive Speed Adjustment

See Figures 14 and 15.

Wheel drive speed is determined by how
deep the wheel drive lower belt rides in the
variable speed (VS) pulley. The higher the
belt rides in the VS pulley groove, the slower
the wheel drive speed. The lower the belt
rides in the VS pulley groove, the faster the
wheel drive speed. To adjust wheel drive
speed:

1. Remove upper and lower drive belt

guards. See

Drive Belt Guards

2. Release the tension from the wheel

drive lower belt. See

Adjust Wheel Drive

Lower Belt Tension

3. Loosen set screw in VS pulley.
4. To decrease wheel drive speed:

•

Rotate the pulley outer half clockwise,
moving it inward. This causes the belt
to ride higher in pulley.

To increase wheel drive speed:

•

Rotate the pulley outer half
counterclockwise, moving it outward.
This causes the belt to ride lower in
pulley.

5. Tighten the VS pulley set screw. Ensure

that set screw fully engages one of the
flats of the shaft.

6. Increase wheel drive lower belt tension.

Adjust Wheel Drive Lower Belt

7. Install drive belt guards.

Wheel Drive Traction Adjustment

The gap between the drive rollers and tires,
when wheel drive is disengaged determines
the amount of contact force when wheel drive
is engaged. Drive roller to wheel gap should
be 1/8 – 1/4" (3 – 6 mm).

NOTE:

A smaller gap between rollers and

tires when wheel drive is disengaged
provides for more engaged traction, which is
helpful on sloped terrain.

1. Remove upper and lower drive belt

guards. See

Drive Belt Guards

2. Loosen fine-adjustment knob to top end

of adjustment link. Do not remove.

3. Remove hairpin, washer and engage

plate from bell crank post.

4. Push the wheel drive frame back until

drive roller gap at wheels is 1/8 – 1/4" (3
– 6 mm). See Figure 17.

NOTE:

Holes in the engage plate allow

traction adjustments to match rear wheel
height.

5. Install nearest hole of engage plate onto

bell crank post. See Figure 16.

6. Install hairpin and washer on bell crank

post.

Figure 14

Figure 15

Flat on

Shaft

1. Wheel Drive

Upper Belt

2. Set Screw

3. VS Pulley

Outer Half

4. Wheel Drive

Lower Belt

«
...
17
18
19
20
21
...
»

Содержание 911707





































Отзывы:

Нет отзывов