Ariens 911707 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 36

Ariens 911707 Скачать руководство пользователя страница 22

GB - 22

5. Hold the flanged nyloc nut (on the inside

of the engine mounting plate) stationary
while turning the belt tensioning bolt
clockwise to increase belt tension.

NOTE:

As the end of the bolt extends against

the mower frame, the engine mount plate is
forced back, increasing belt tension.

•

Adjust belt to 30-35 lbs tension. This
equates to belt deflection of
approximately 0.5 inches measured at
the center of the longest belt span (RH
side of machine as viewed from
operator position). See Figure 19.

6. Turn bolt counterclockwise to decrease

belt tension.

NOTE:

Check belt deflection with

approximately 3 lbs of force (average finger
force).

7. Tighten engine mounting hardware to

14

lbf-ft (19 N•m).

8. Release PTO clutch control lever.
9. Install lower belt drive guard. See

10. Test PTO clutch. The blade must stop

within 3 seconds after releasing control
lever. If blade continues to run, adjust or
repair control components immediately.
See

PTO CLUTCH CABLE

BELT REPLACEMENT

Wheel Drive Lower Belt Replacement

1. Remove upper and lower drive belt

guards. See

Drive Belt Guards

NOTE:

The adjustment bracket bolt holes are

threaded.

2. Loosen the lock nut and bolt attaching

each adjustment plate to the adjustment
bracket. Do not remove hardware.

3. Loosen the flanged nut on each

adjustment hex bolt away from the
adjustment bracket.

4. Turn both adjustment bolts out evenly

until belt becomes loose enough to slide
off blade shaft pulley.

CAUTION:

If wheel drive lower belt is

installed incorrectly, the variable speed (VS)
pulley will rotate in reverse. The drive rollers
shaft will then also be driven in reverse. If
driven in reverse, the drive rollers will slip and
produce a clicking noise.

5. Twist belt 90º so left side goes to lower

side of VS pulley. Also see Figure 19.

Figure 20

1. Mounting

Hardware

2. Engine

Mounting
Plate

3. Flanged Nyloc

Nut

4. Frame
5. Belt

Tensioning
Bolt

«
...
20
21
22
23
24
...
»

Содержание 911707





































Отзывы:

Нет отзывов