manualshive.com logo in svg

Ariens 911087 - LM21S, Руководство владельца и оператора

Поделиться
Скачать
Ariens 911087 - LM21S Скачать руководство пользователя страница 22

GB - 22

WHEEL DRIVE CONTROL 
ADJUSTMENT (self-propelled 
models)

See Figure 14.

The wheel drive must start to engage when 
wheel drive control is between 1-1/2” and 2” 
(3.8 and 5 cm) away from the handlebar.
To check:

1. With engine off, select a slow speed.
2. Slowly pull unit backwards.
3. Slowly squeeze wheel drive control until 

wheels stop.

4. Measure the distance between the wheel 

drive control and handlebar at the 
handlebar indentation.

To adjust:

1. If the measurement is more than 2” 

(5cm), loosen the lower cable nut and 
then tighten the upper cable nut against 
the adjuster bracket.

2. If the measurement is less than 1-1/2” 

(3.8cm), loosen the upper cable nut and 
then tighten the lower nut against the 
adjuster bracket.

3. Recheck measurement with the slowest 

and fastest speeds selected.

4. Repeat adjustment until wheel drive 

control is properly adjusted.

IMPORTANT: 

If there is not enough thread 

length for proper adjustment, contact your 
Dealer for repairs before operating unit.

SPEED CONTROL BELL CRANK 
(self propelled units)

The speed control bell crank holds the speed 
control rod in position after a speed has been 
set. The spring washers may become loose 
with normal wear. If the speed control rod 
does not stay firmly in position, adjust the 
speed control bell crank. See Figure 15.
To adjust:

1. Remove cover, fully compress the 

helical spring lock washers with lock 
nut and then back lock nut off, one 
quarter turn.

2. If the speed control rod is still too loose, 

tighten lock nut by small increments 
until it holds its position. Tightening the 
lock nut too much will not allow the 
speed control rod to move at all.

3. Align notch in left hand side of cover 

with bolt and secure with knob.

1. Traction Cable
2. Handlebar Indentation
3. Cable Nuts
4. Wheel Drive Control

1-1/2" to 2"

2

4

3

1

OM0290

(3.8 to 5cm)

Figure 14

1. Lock Nut
2. Helical Spring 

Lock washers

3. Speed 

Control Bell 
Crank

4. Speed 

Control Rod

5. Hair Pin
6. Swivel

1

2

3

4

5

6

OM0300

Figure 15

Содержание 911087 - LM21S





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды