Argox AS-9500 Скачать руководство пользователя страница 120

Страница: 120 / 144

119

OCR User-Defined Variables

You can create up to two of your own user variables for an OCR

template. These variables will represent any OCR readable

characters. The user-defined variables are stored under the letters

“g” and “h.” Creating a user variable follows the same steps as

creating a template, but instead of scanning the

Enter OCR

Template

symbol, you scan the

Enter User-Defined Variable

symbol. The letters g and h can then be used in an OCR template

to define the

variable you specified.

Example:

You need a variable to represent the letters “A,” “B,” or

“C.” The template for this variable would be:

414243 To create this template, you would enable the OCR-A font.

Scan the

Enter

User-Defined Variable g

symbol. Scan

414243

(the hex characters for “A,” “B,” and “C”). Scan

Save OCR

Template

. This will let you read either

A or B or C in any position where you place the g. For example,

you could create the following template: ddddddggg This template

would then let you read data that began with six digits, and had an

A, B, or C trailing. So you would be able to read:

Содержание AS-9500

















































































































































Результаты поиска

Содержание AS-9500

Отзывы:

Похожие инструкции для AS-9500

Бренды по названию

Популярные бренды

Argox AS-9500, Руководство пользователя

Результаты поиска

Содержание AS-9500

Отзывы:

Похожие инструкции для AS-9500

Бренды по названию

Популярные бренды