background image

Safety and Care Advice

Important

– Please read these instructions fully before starting assembly

Note:

If required the next page

can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

1

Check you have all the

components and tools listed on
pages 2 and 3.

Remove all fittings from the

plastic bags and separate them
into their groups.

Keep children and animals

away from the work area, small
parts could choke if swallowed.

Make sure you have enough

space to layout the parts before
starting.

Do not stand or put weight on

the product, this could cause
damage.

Assemble the item as close

to its final position (in the same
room) as possible.

Assemble on a soft level

surface to avoid damaging the
unit or your floor.

We do not

recommend the
use of power
drill/drivers

for

inserting screws

,

as this could damage the unit.
Only use hand screwdrivers.

Parts of the assembly will be

easier with 2 people.

Dispose of all packaging

carefully and responsibly.

This product has been produced

from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.

The product has been treated

with a wax and oil finish to
prevent dirt ingress and preserve
moisture.

On unpacking the

furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.

This process may leave some

staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.

Care and maintenance

Use an appropriate furniture

polish for natural wood
furniture and a dry cloth to
clean the product.

Avoid placing the furniture in

direct sunlight as this will cause
the timber to prematurely age.

From time to time check

that there are no loose
screws on this unit.

This product should not be

discarded with household
waste. Take to your local
authority waste disposal
centre.

Содержание SAN DIEGO 412/2214
















Отзывы: