background image

2

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

Note: if required the next 
page can be cut out and used 
as reference throughout the 
assembly. Keep this page with 
these instructions for future 
reference.

• Check 

you have all the 

components and tools listed on 
pages 2 and 3. 

plastic bags and separate them 
into their groups.

• Keep child

ren and animals 

away from the work area, small 
parts could choke if swallowed.

• 

Make sure you have enough 

space to layout the parts before 
starting. 

• 

Do not stand or put weight on 

the product, this could cause 
damage.

• 

Assemble the item as close 

room) as possible.

• 

Assemble on a soft level 

surface to avoid damaging the 

• 

Parts of the assembly will be 

easier with 2 people.

 •

 We do not 

recommend the 
use of power 
drill/drivers for 
inserting screws,

as this could damage the unit. 
Only use hand screwdrivers.

• Dispose of all pac

kaging 

carefully and responsibly.

• Only clean using a damp cloth 

and mild detergent, do no use 
bleach or abrasive cleaners. 

• 

From time to time check that 

there are no loose screws on 
this unit.

 This product should not be 

discarded with household 
waste. Take to your local 
authority waste disposal centre.

Care and maintenance

Skin contact: Remove 
contamination by washing with 
soap and water. This procedure 
should also be followed prior to 
eating and drinking.

Eye contact: Rinse immediately 
with clean water for 15 minutes 
and seek medical advice. 

If swallowed: Seek medical 
advice immediately. 

Glue safety - Take care when using glue, please follow the advice below

Содержание Hallingford 305/2763
















Отзывы: