Argo AE2MI56AH Скачать руководство пользователя страница 21

Страница: 21 / 24

Fig. 34a

Fig. 34b

Fig. 35

Fig. 36

Indoor unit

R.OUT connector
on circuit board

Indoor unit
extended-connection
cord (8 m):
Available separately
STK-WS0508W

Remote controller
IN connector

Indoor unit

5. Address Setting of the Remote Control

Unit

5-1. Setting the Remote Controller Address

The address can be set in order to prevent interference

between remote controllers when two Sanyo A/C units

are installed near each other. The address is normally

set to “A.” To set a different address, it is necessary to

change the address on the second remote controller.

(1) Break the address-setting tab “A” on the second

remote controller to select the remote controller

address “B.” (Fig. 34b)

(2) Insert dry-cell batteries into the second remote con-

troller and press the reset button. Then reattach the

cover.

(3) Open the air intake grille on the second indoor unit.

Move the operation switch to the “DEMO” position.

(Fig. 35)

(4) Press the Start/Stop button on the remote con-

troller. Check that the “beep” signal-received sound

is heard from the second indoor unit.

(5) Move the operation switch to the “ON” position, and

close the intake grille. (Fig. 35)

(6) Operate the remote controller. Check that the

“beep” signal-received sound is heard from the sec-

ond indoor unit.

5-2. Operating Multiple Indoor Units with a Single

Remote Controller

Insert the indoor unit extended-connection cord (avail-

able separately) into the R.OUT connector on the

indoor unit circuit board. Insert the other end into the

indoor unit remote controller IN connector. Repeat this

procedure. A total of up to four units can be controlled.

Be sure as part of the test run to check the installa-

tion using the Installation Check Sheet (next page).

Case

Содержание AE2MI56AH

























Результаты поиска

Содержание AE2MI56AH

Отзывы:

Бренды по названию

Популярные бренды

Argo AE2MI56AH, Руководство по установке

Результаты поиска

Содержание AE2MI56AH

Отзывы:

Бренды по названию

Популярные бренды