Page 4
device is not sending a good signal, check to see if the volume level on the TV/audio source is adjusted too low. The
level should be set to approximately 75% of the maximum. Turn up the volume, then turn off the speakers on the
device by changing the setting through the on-
screen menus (see owner’s manual for instructions.) If the problem
persists, contact the technical service department for TV/audio device or ARG for assistance.
Setting the Broadcast Frequency
–
Unlock the transmitter by pressing and holding the “LOCK” button until the lock
icon disappears from the display. The second digit in the frequency display will start to flash. (All 900MHz
frequencies
begin with “9” therefore the cursor defaults to the second digit.) Enter the number on the keypad to set
the second digit for the chosen frequency. As digits for the frequency are set, the cursor automatically moves to the
right until all of the digits in the new frequency have been entered. The decimal point remains in the same place and
is always present; there is no need to enter the last digit as it is always zero (0). If the wrong number is entered,
move the cursor back by pressing the “OUTPUT DOWN” arrow. Then enter the correct number. Move the cursor
ahead by pressing the “OUTPUT UP” arrow. When all of the digits have been entered correctly, press the “ENTER”
button.
(NOTE: Once the “ENTER” button has been pressed, the cursor will disappear. To change, press the “SET”
button to start over.)
Finally, press the “MEMO” button to save frequency. The frequency MUST be saved by
pressing the “MEMO” button or it will have to be re-entered each time power is cut-off to the transmitter.
OTHER FUNCTIONS:
Changing the Output Level -
This setting controls the loudness or volume level of the transmitter’s audio signal.
Use as an auxiliary volume control if the TV/Audio device has a
fixed
audio output that is either too high or too low.
The output level setting is displayed as two large numbers on the left side of the display, ranging from zero to 15.
Adjust the output level when the transmitter is in the “LOCK” mode (Lock icon shows in the display). Lower the
output level by pressing the “OUTPUT DOWN” arrow (#6) and increase by pressing the “OUTPUT UP” arrow (#7).
(Note: The factory output level is “08”. If the level is too low it will be difficult to hear the sound; if set too high, the
sound will be distorted and hard to understand.)
This setting is also useful for evening out the volumes of different
televisions in a multiple device system as TV channels are broadcast at different volume levels.
LIMITED WARRANTY
Audio Resource Group, Inc. warrants all new ARG products to be free from defects in materials and manufacture for the warranty periods set forth
below. The warranty periods commence on the invoice dates of the original purchase. This warranty applies only against defects discovered within
the warranty period and notification to ARG must be given within 30 days after the date of discover of any nonconformity. Parts repaired or replaced
under the terms of this warranty will be warranted for the remainder of the original warranty period only. Product that fails after the warranty period will
be repaired or replaced at the current part and labor pricing after inspection by ARG and authorization from the customer. Audio Resource Group,
Inc.’s obligations under this warranty are limited as set forth below:
ARG-CV-FMT
FM Transmitter
Purchased Prior to 2014
2 Year
ARG-CV-FMT
FM Transmitter
Purchased after 1/1/2014
4 Years
Warranty only applies to the original buyer. Warranty is void if products have been damaged due to accident, misuse, abuse, improper service,
mechanical or electrical non-ARG, Inc. authorized modification. ARG, Inc. is not liable, without limitation to any person or entity, for any direct,
incidental, consequential damages or medical expenses caused by any use, defect, failure or malfunction of the product. This warranty does not cover
cosmetic damage of the product or if the serial number or model number affixed to the product has been removed, defaced, changed, altered or
tampered with. This warranty does not cover installation or signal reception problems. The terms of the warranty are governed by the laws of the state
of North Dakota, USA.
ARG will only accept returned products with prepaid shipping and a return authorization number. Contact ARG, Inc. at 888-468-4552 for a return
authorization number or for additional information.
Mail or Ship To:
Audio Resource Group, Inc.
Attn: Repair Department
405 Main Ave W Unit 4G
West Fargo, ND 58078
Phone: (888) 468-4552
Fax: (888) 373-4819
Email: [email protected]
