Thanks for buying an Ardistel product.
This accessory you have just acquired is an indispensable product for your 3DS™ system. It gives extra energy for
charging the battery pack of your system without need of using annoying wires or charge adaptors.
It’s the perfect accessory for travels and outdoor activities.
PACK CONTENTS
1 x 3D-Xtra Life Stand with built-in 2000mAh capacity battery pack
1 x USB-DC Charging Cable for 3DS™ system (aprox. length 1,20m).
1 x Instructions Manual
PRODUCT FEATURES
• Built-in battery pack with 3.7V 2000mAh Li-Polimer.
• Input: aprox. 5 V
≤
400mA
• Maximum output: 4,7+ / 0.1V
≤
800mA
• POWER Button for on/off.
• Quickly charges your 3DS™ system.
• With 4 blue color LEDs to indicate the energy level of the built-in battery pack.
• Including LED indicator for battery charge.
SETUP INSTRUCTIONS FOR CHARGING THE SYSTEM
1.
Place your 3DS™ system in the 3D-Xtra Life Stand, making sure to place it in its correct position and taking care
specially to the area of the charging pin connectors in the Stand, in order not to damage them.
2.
To power on the Stand, press the “POWER” button in the front side of it, the energy level LEDs from the Stand (with
the label “ENERGY LEVEL”, in front part too) will turn on in blue color indicating that the charging process has started.
Also, these LED indicate the remaining charging level of the built-in battery pack: depending on the number of LED
turned on, the battery pack will have more or less energy available.
3.
If the LED indicator in your system is red, the charging process has started.
4.
If the LED indicator in your system is green, the system is fully charged.
NOTE: For more information about the system charge process, check the original manual from your 3DS™ system.
CHARGING THE STAND WITH BATTERY PACK
• With the Stand powered on (“POWER” button), if the 4 LED indicators from the Stand (labelled as “ENERGY LEVEL”,
in front side) are turned on in blue colour, then the battery pack is fully charged. Otherwise, if just only the first LED is
illuminated (from left to right) or there is no LED turned on, the level of the battery pack is minimal or the battery pack
is fully drained, and you will need to charge the 3D-Xtra Life Stand again. If there is 2 LED, the energy level is low, if
there is 3 LED, the energy level is high but not full.
• In order to charge the 3D-Xtra Life Stand, connect the USB-DC cable included, one side into the connector labelled as
“DC IN 5V” in the back side of the Stand, and the other side to a free USB port from any PC computer.
• Also, the 3D-Xtra Life Stand can be charged using the official charging AC adapter from your 3DS™ system. Make sure
that the charge adapter that you are going to use is with the correct voltage because a different voltage might damage
seriously your system and the Stand. In order to check that the voltage is the correct one, check the technical
specifications at the beginning of this manual, visit the website
www.ardistel.com
, or contact directly with
• If the LED charging indicator in the Stand (located in the front side, to the left, see diagram) is turned on red colour,
it will indicate that the charge process has started.
• When the mentioned charging LED turns on green colour, it will indicate that the charging process of the built-in
battery pack in the 3D-Xtra Life Stand is completed. Then, disconnect the USB-DC charging cable or the 3DS™ official
charging adapter to avoid overheating the unit.
• The charging time approximated for the built-in battery pack in the 3D-Xtra Life Stand is about 6 hours.
VERTICAL POSITION FOR THE 3D-XTRA LIFE STAND
Thanks to the extensible piece located at the bottom of the 3D-Xtra Life Stand, you will be able to place your 3DS™
system in angle view according to the point of view of the user, in order to be more comfortable use and visualization
of the system when it is placed into the Stand.
WARNINGS AND SAFETY MEASURES
• Warning: Charging voltage must be lower than 5,6V and the charging current must be lower than 400mAg. Do not
overheat the unit with AC charging adapters with more capacity than indicated in this manual.
• Avoid dropping off the Stand onto hard surfaces.
• Do not throw any parts of this device into water, fire and never let them drop.
• Keep the product in a safe and dry place. Do not expose to direct sun light.
• Do not leave powered on the Stand when you are not using it. Press the “POWER” button in the front side to power
it off. Also never leave connected the charging cables or the AC adapters when you are not charging the Stand to avoid
overheating the unit. Please use the product accordingly and following the steps in this manual and in the same order.
• This product is for INDOOR USE ONLY. Recycle it correctly; do not throw as if it were domestic waste because it
contains electronic components. Check any collecting points in your area.
• Children must be ALWAYS supervised by an adult.
3D-XTRA LIFE STAND WITH BATTERY PACK ARDISTEL FOR 3DS™
INSTRUCTIONS MANUAL
BUTTONS AND FUNCTIONS DESCRIPTIVE DIAGRAM
BOTTOM SIDE
TOP SIDE
REAR SIDE
FRONT SIDE
POWER
ENERGY LEVEL
0-14
Entrada: 5V ≤ 400mA
Salida: 4.7+/0.1V ≤ 800mA
BATERÍA RECARGABLE
2000mAh PARA 3DS™
DC IN 5V
Extensible piece
for vertical position
Compartment
for the system
DC IN 5V Connector
for charging cables
Charging LED indicator
for the Stand
Anti-slippery
rubber spots
Battery pack energy level
LED indicators
Power on/off button
“POWER”
Charge connectors (pins)
for the system
Charge connectors (pins)
for the system
