Owner's Manual
TX158, TX159 ATV Trailers
TX191 Tracking Beam Kit
Check for parts online at
www.yutrax.com
or call 800-345-6007 M-F 8-5 CST
Page 3
foR TX159
5. Support the trailer far enough off the ground for the
assembly of the tracking beams, braces and wheels.
Slide the tracking beam and brace onto the threaded
axle spindle. Secure in place following this order:
tracking beam, tracking beam brace, 3/4” crown nut
and cotter pin. Back crown nut off just enough so
tracking beam will pivot freely and crown nut slot
aligns with hole in threaded axle spindle. Insert cotter
pin. Using a needle nose pliers, bend cotter pin ears
around so it will not come off the axle spindle. Repeat
this step for remaining tracking beam.
SEE fIgURES
2 AND 3.
6. Slide the wheel onto the threaded axle spindle of
tracking beams with grease fitting facing outward.
Secure in place following this order: wheel, 3/4” washer,
3/4” crown nut and cotter pin. Back crown nut off just
enough so wheel spins freely and crown nut slot aligns
with hole in threaded axle spindle. Insert cotter pin.
Using a needle nose pliers, bend cotter pin ears around
so it will not come off the axle spindle. Repeat this step
for remaining three wheels.
SEE fIgURES 2 AND 3.
IMPORTANT NOTE: You must grease the bearings of
each wheel. Using a grease gun, pump high quality
grease into the bearings by attaching to grease
fitting located on wheel hub. Check the grease level
frequently to prevent bearings from seizing.
foR BoTH MoDElS
7 Attach front trailer frame and the rear trailer frame
together using () provided 1/4-0 x ” bolts, () 1/4-
0 x -1/” bolts, (4) nyloc nuts and (8) 1/4” washers.
SEE fIgURE 1 oR 2.
8. Attach the front trailer frame (300713) to the axle plates
using () provided 1/4-0 x 1-1/” bolts, () 1/4-0 x ”
bolts, (4) nyloc nuts and (4) 1/4” washers.
SEE fIgURE 1
oR 2.
Latch the front trailer frame to the latch located on
trailer tongue to hold in place.
9. Attach the rear trailer frame (300710) to the axle plates
using () provided 1/4-0 x 1-1/” bolts, () 1/4-0 x ”
bolts, (4) nyloc nuts and (4) 1/4” washers.
SEE fIgURE
1 oR 2.
You must now tighten all nut & bolt
assemblies. Be sure not to over tighten or crush
tubing when tightening!
10. Slide the removable tailgate (300704) into the slots
of rear trailer frame. Slide the removable side rails
(300700 & 300701) into the top side of front and rear
trailer frames.
SEE fIgURE 1 oR 2.
NOTE: The side rail that goes in the front of trailer
frame is narrower than the others. Lubrication is
recommended at slide-together points.
USE INSTRUCTIoNS:
1. To use the tilt/pivot feature, simply unlatch the latch
located on trailer tongue. This will allow you to tilt the
trailer frame upward to unload. If pivoting is desired,
simply unlatch the latch and turn the trailer frame to
the desired location, left or right, and tilt trailer frame
upward to unload. This feature works well when in
tight areas. Or if backing up your trailer is not an
option, simply drive along side desired unloading
area, unlatch the trailer frame and turn trailer frame to
desired location.
Always…
• Be sure the trailer is securely attached to ATV hitch.
• Check tires for correct air pressure before each use.
• Use as 4-wheeled ATV trailer only.
• Inspect before each & every use to be sure there is no
product damage or loose/missing bolts & hardware.
• Have wheel bearings properly greased to avoid bear-
ings from seizing.
Never…
• Use excessive speeds while towing trailer.
• Exceed the maximum load capacity of 150 Ibs.
• Allow people or animals to ride in trailer.
• Use on hilly terrain.
• Use a damaged product.
• Use when intoxicated or using over-the-counter
medication or prescription drugs.
• Use on rocky or obstacle ridden terrain.
• Use carelessly -- Think Safety!
oPTIoNAl ACCESSoRIES
TX11 Ball Hitch Kit
TX191 Extreme Tracking Beam Kit (for TX158 only)
