Arctic King ABDA049AS Скачать руководство пользователя страница 14

 

14

6.  Disconnect the beer line and CO

2

 air line from the keg coupler. 

7.  Remove the beer keg and bottom metal plate. 
8.  Remove the keg coupler. 
9.  Disconnect the air line from the CO

2

 cylinder. 

10.  Remove the CO

2

 air line from cabinet plug 

11.  Replace the air line rear cabinet plug 
12.  Remove the beer tower. Also pull the beer line thru the top of the cabinet. 
13.  Replace the top cabinet plug. 
14.  Remove the guard rail and cover the guard rail installation holes by the provided plugs. 
15.  Install the two wire shelves to the desinaged positions.  
16.  Adjust temperature as desired. 

 
 

OPERATING YOUR BEER DISPENSER

 

 

 

Setting The Temperature 

To  start,  turn  the  temperature  control  knob  to  the  maximum  setting  (6)  to 
achieve  coldest  position  quickly.  Allow  the  unit  to  run  for  3  hours. 
Temperature  range  of  the  thermostat  goes  from  36°F  to  45°F  (2.2ºC  to 
7.2ºC). 
 
Optimum  temperature  for  serving  draught  beer  is  between  34°F  –  38°F 
(1.1ºC – 3.3ºC) and that is a key factor to consider in storing and dispensing 
draught beer. 
 
To turn off the Beer Dispenser, turn the control knob to the “OFF” position. 
 

NOTE:

 Keep an accurate thermometer handy and adjust temperature control setting as necessary or 

according to your needs. 
 

 

Automatic Defrosting 

There is no need to defrost the Beer Dispenser. Defrost water collects and passes through the drain 
outlet in the rear wall into a tray located above the compressor, where it evaporates. 

 
NOTE: 

 

IF  THE  UNIT  IS  UNPLUGGED,  POWER  LOST,  OR  TURNED  OFF,  YOU  MUST  WAIT  3  TO  5 
MINUTES BEFORE RESTARTING THE UNIT. IF YOU ATTEMPT TO RESTART BEFORE THIS 
TIME DELAY, THE BEER DISPENSER WILL NOT START. 

 

TURNING  THE  TEMPERATURE  CONTROL  TO  “OFF”  POSITION  STOPS  THE  COOLING 
CYCLE BUT DOES NOT SHUT OFF THE POWER TO THE UNIT. 

 

 

 

 

CARE AND MAINTENANCE 

 

 

Cleaning Your Beer Dispenser 

 

Turn the temperature control to "OFF", unplug the Beer Dispenser, and remove the contents. 

 

Wash  the  inside  surfaces  with  a  warm  water  and  baking  soda  solution.  The  solution  should  be 
about 2 tablespoons of baking soda to a quart of water. 

 

Wash the shelves and metal plate with a mild detergent solution. 

 

Wring  excess  water  out  of  the  sponge  or  cloth  when  cleaning  area  of  the  controls,  or  any 
electrical parts. 

 

Wash the outside cabinet with warm water and mild liquid detergent.  Rinse well and wipe dry with 
a clean soft cloth. 

 

 

Vacation Time 

 

Short vacations: 

Leave the Beer Dispenser operating during vacations of less than three weeks.

 

Содержание ABDA049AS
























Отзывы: