Arctic Cat 2262-967 Скачать руководство пользователя

Страница: 33 / 50

Checking/Changing Brake

Pads

The condition of the brake pads must be

checked daily and changed if worn or

damaged. To check and change the brake

pads, use the following procedure:



NOTE: The brake pads may be

changed by the snowmobile owner if

qualified to do so. If the owner does

not feel qualified, take the snowmo-

bile to an authorized Arctic Cat

Snowmobile dealer for this service.

This service is at the discretion and

expense of the snowmobile owner.



NOTE: When installing new brake

pads, always install them as a set.

Never install just one pad or use

brake pads which have been used in

another snowmobile.

1. Remove the brake fluid reservoir cover;

then remove most of the brake fluid

from the reservoir. Install the cover.



NOTE: The above procedure will

allow room for the fluid from the cali-

per when the pistons are pushed

into the caliper for installing new

brake pads. Replacing the cover will

prevent fluid spillage.

2. Open the left-side access panel.
3. Remove the Torx-head screws

securing the brake shield to the belt

guard mount; then remove the cap

screws securing the brake shield to

the brake caliper.

4. Carefully move the shield out of the

way; then remove the hairpin clip

securing the brake pads to the cali-

per assembly.

5. Pull the brake pads out of the caliper

assembly.

ZR-390

6. Measure the thickness of the brake pad.

The brake pad thickness must be greater

than 1.0 mm (0.04 in.). If the brake pad

thickness is less than specified, replace-

ment of both pads is necessary.

PC011A

7. Position the outer brake pad into the

caliper; then install the hairpin clip

into the caliper assembly.

8. Repeat for the inner pad; then secure

the pad with the hairpin clip.

9. Remove the reservoir cover and

remove the remaining fluid; then fill

the reservoir with fresh fluid and

install the cover.

10. Pump the brake lever to ensure cor-

rect positioning of the brake pads and

proper brake lever travel; then release.



NOTE: If brake lever travel is not

within specification, bleed the brake

system.

11. Remove the reservoir cover and fill

the reservoir (if necessary) to the

proper level with fresh brake fluid;

then install the cover.

12. Secure the brake shield; then close and

secure the left-side access panel.



NOTE: When new brake pads are

installed, a “burnishing” process is

required (see Burnishing Brake Pads

sub-section).

CAUTION

Brake fluid is highly corrosive. Do not

spill brake fluid on any surface of the

snowmobile.

Содержание 2262-967



















































Результаты поиска

Содержание 2262-967

Отзывы:

Похожие инструкции для 2262-967

Бренды по названию

Популярные бренды

Arctic Cat 2262-967, Руководство оператора

Результаты поиска

Содержание 2262-967

Отзывы:

Похожие инструкции для 2262-967

Бренды по названию

Популярные бренды