Arcteq AQ-G215 Скачать руководство пользователя страница 415

Страница: 415 / 458

8.11 Double ST 100 Mbps Ethernet communication module (optional)

Figure. 8.11 - 255. Double ST 100 Mbps Ethernet communication module connectors.

Connector

Description

Two-pin connector

• IRIG-B input

ST connectors

• Duplex ST connectors (IRIG-B input)

• 62.5/125 μm or 50/125 μm multimode fiber

• Transmitter wavelength: 1260…1360 nm (nominal: 1310 nm)

• Receiver wavelength: 1100…1600 nm

• 100BASE-FX

• Up to 2 km

This option cards supports redundant ring configuration and multidrop configurations. Redundant

communication can be implemented by Ethernet switches that support Rapid Spanning Tree Protocol

(RSTP). Please note that each ring can only contain AQ-200 series devices, and any third party

devices must be connected to a separate ring.

For other redundancy options, please refer to the option card "LC 100 Mbps Ethernet communication

module".

The images below present two example configurations: the first displays a ring configuration (note how

the third party devices are connected in a separate ring), while the second displays a multidrop

configuration.

Q-G215

-G215

Instruction manual

Version: 2.04

414

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды