Arcteq AQ-G215 Скачать руководство пользователя страница 335

Страница: 335 / 458

Figure. 5.4.9 - 208. Logic output example.

5.4.10 Logical inputs

Logical inputs are binary signals that a user can control manually to change the behavior of the

AQ-200 unit or to give direct control commands. Logical inputs can be controlled with a virtual switch

built in the mimic and from a SCADA system (IEC 61850, Modbus, IEC 101, etc.). Logical inputs are

volatile signals: their status will always return to "0" when the AQ-200 device is rebooted.

Logical inputs have two modes available: Hold and Pulse. When a logical input which has been set to

"Hold" mode is controlled to "1", the input will switch to status "1" and it stays in that status until it is

given a control command to go to status "0" or until the device is rebooted. When a logical input which

has been set to "Pulse" mode is controlled to "1", the input will switch to status "1" and return back to "0"

after 5 ms.

The figure below presents the operation of a logical input in Hold mode and in Pulse mode.

Figure. 5.4.10 - 209. Operation of logical input in "Hold" and "Pulse" modes.

A logical input pulse can also be extended by connecting a DELAY-low gate to a logical output, as has

been done in the example figure below.

Q-G215

-G215

Instruction manual

Version: 2.04

334

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды