Arcoweld ArcoTiG HF 315 AC/DC Скачать руководство пользователя страница 38

Страница: 38 / 43

S/N

Troubles

Reasons

Solution

Turning on the power source,
the power lamp is not on, and
fan doesn’t work

No power supply input

Check whether there is power supply

The fuse inside the machine damaged

Change it (3A)

The number on the display is not

intact.

The LED in the display is broken

Change the LED

The max and min value displayed

doesn’t accord with the set
value.

The max value is not accordant (refer to 3.1)

Adjust potentiometer Imin on the power
board.

The min value is not accordant (refer to 3.1)

Adjust potentiometer Imaxin the current
meter.

No no-load voltage output
(MMA)

The machine is damaged

Check the main circuit and the Pr4.

Arc can not be
ignited (TIG)

There is spark
on the HF
igniting board.

The welding cable is not connected with the

two output of the welder.

Connect the welding cable to the
welder’s output.

The welding cable damaged.

Repair or change it.

The earth cable connected unstably.

Check the earth cable.

The welding cable is too long.

Use an appropriate welding cable.

There is oil or dust on the workpiece.

Check and remove it.

There is not
spark on the
HF igniting
board.

The HF igniting board does not work.

Repair or change Pr8

The malfunction of the welding torch switch.

Check the welding torch switch, control
cable and aero socket.

No gas flow (TIG)

Gas cylinder is closed, or gas pressure is low

Open or change the gas cylinder

Something in the valve

Remove it

Electromagnetic valve is damaged

Change it

Gas flows continuously

The gas-test on the front panel is on

The gas-test on the front panel is off

Something in the valve

Remove it

Electromagnetic valve is damaged

Change it

The adjustment knob of pre-gas time on the
front panel is damaged

Repair or change it

The welding current can not be
adjusted

The welding current potentiometer on the
front panel connection is not good or
damaged

Repair or change the potentiometer

No AC output while selecting
“AC”

The power PCB is in trouble.

Repair or change it.

The AC drive PCB damaged.

Change it.

The AC IGBT module damaged.

Change it.

The welding current displayed
isn’t accordant with the actual
value.

The min value displayed isn’t accordant with
the actual value. (Please refer to 3.1)

Adjust potentiometer Imin on the power
board.

The max value displayed isn’t accordant with
the actual value. (Please refer to 3.1)

Adjust potentiometer Imax on the power
board.

Содержание ArcoTiG HF 315 AC/DC












































Результаты поиска

Содержание ArcoTiG HF 315 AC/DC

Отзывы:

Похожие инструкции для ArcoTiG HF 315 AC/DC

Бренды по названию

Популярные бренды

Arcoweld ArcoTiG HF 315 AC/DC, Руководство оператора

Результаты поиска

Содержание ArcoTiG HF 315 AC/DC

Отзывы:

Похожие инструкции для ArcoTiG HF 315 AC/DC

Бренды по названию

Популярные бренды