Arcoaire A Series Скачать руководство пользователя страница 14

Страница: 14 / 40

N80ESN/N80ESL(Series A): Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

*135 and 155 size furnaces requires a 5 or 6-in. (127 or 152 mm) vent. Use a vent adapter between furnace and vent stack. See Installation Instructions for complete installation requirements.

Upflow Furnaces

The return-air duct must be connected to bottom, sides (left or right), or a

combination of bottom and side(s) of main furnace casing (see

Fig. 19

and

Fig. 20

). Bypass humidifier may be attached into unused return air

side of the furnace casing (see

Fig. 19

and

Fig. 20

). Not all horizontal

furnaces are approved for side return air connections (see

Fig. 20

A02163

Fig. 18 – Downflow Return Air Configurations and Restrictions

A02075

Fig. 19 – Upflow Return Air Configurations and Restrictions

A02162

Fig. 20 – Horizontal Return Air Configurations and Restrictions

GAS PIPING

Gas piping must be installed in accordance with national and local

codes. Refer to current edition of NFGC.
Installations must be made in accordance with all authorities having

jurisdiction. If possible, the gas supply line should be a separate line

running directly from meter to furnace.

NOTE:

In the state of Massachusetts:

1. Gas supply connections MUST be performed by a licensed plumber or gas

fitter.

2. When flexible connectors are used, the maximum length shall not exceed 36

inches (915 mm).

3. When lever handle type manual equipment shutoff valves are used, they

shall be T-handle valves.

4. The use of copper tubing for gas piping is NOT approved by the state of

Massachusetts.

Table 5 – Dimensions

Unit Size

CABINET WIDTH

OUTLET WIDTH

TOP AND

BOTTOM FLUE

COLLAR

BOTTOM

INLET WIDTH

VENT

CONNECTION

SIZE

SHIP WT. LB.

(KG)

0451412

14-3/16 (360)

12-9/16 (319)

9-5/16 (237)

12-11/16 (322)

4 (102)

104 (47)

0451712

17-1/2 (445)

15-7/8 (403)

11-9/16 (294)

16 (406)

4 (102)

119 (54)

0701412

14-3/16 (360)

12-9/16 (319)

9-5/16 (237)

12-11/16 (322)

4 (102)

114 (52)

0701712

17-1/2 (445)

15-7/8 (403)

11-9/16 (294)

16 (406)

4 (102)

120 (54)

0701716

17-1/2 (445)

15-7/8 (403)

11-9/16 (294)

16 (406)

4 (102)

126 (57)

0702116

21 (533)

19-3/8 (492)

13-5/16 (338)

19-1/2 (495)

4 (102)

142 (64)

0901714

17-1/2 (445)

15-7/8 (403)

11-9/16 (294)

16 (406)

4 (102)

131 (49)

0902116

21 (533)

19-3/8 (492)

13-5/16 (338)

19-1/2 (495)

4 (102)

137 (62)

0902120

21 (533)

19-3/8 (492)

13-5/16 (338)

19-1/2 (495)

4 (102)

140 (64)

0902420

24-1/2 (622)

22-7/8 (581)

15-1/16 (383)

23 (584)

4 (102)

146 (66)

1102120

21 (533)

19-3/8 (492)

13-5/16 (338)

19-1/2 (495)

4 (102)

146 (66)

1102420

24-1/2 (622)

22-7/8 (581)

15-1/16 (383)

23 (584)

4 (102)

161 (73)

1352420

24-1/2 (622)

22-7/8 (581)

15-1/16 (383)

23 (584)

4 (102)

167 (76)

1552420

24-1/2 (622)

22-7/8 (581)

15-1/16 (383)

23 (584)

4 (102)

168 (76)

DOWNFLOW RETURN AIR CONFIGURATIONS AND RESTRICTIONS

Содержание A Series









































Результаты поиска

Содержание A Series

Отзывы:

Похожие инструкции для A Series

Бренды по названию

Популярные бренды

Arcoaire A Series, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание A Series

Отзывы:

Похожие инструкции для A Series

Бренды по названию

Популярные бренды