Archgard Optima 70-2 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 53

Archgard Optima 70-2 Скачать руководство пользователя страница 38

Optima 70 - 2

38

SURROUND KIT INSTALLATION

The Optima 70 can have an optional surround kit installed. After opening the surround kit pack-
age, inspect the product to ensure that no damage has occurred inside the package. Please re-
port any damage immediately to your Authorized Dealer.

The optional surround kit will contain;

•

(1) One Piece Bottom Trim.

•

(2) Two Pieces, Left & Right Side Trims.

•

(1) One Piece Top Trim.

•

(2) 1/4” (6mm) hex head screws. (for use with the Euro 65) discard for the Optima 70.

Tools Required: 1/4” (6 mm) hex head hand screw driver.

NOTE: Before starting, remove the plastic film that protects the trim pieces. Wipe any finger
prints before turning on the appliance, so as not to etch the prints on to the trims.

1.

Remove the upper & lower louvers including the two lower hinges and set aside.

2.

Place the bottom trim piece in position.

3.

Remove the paper backing from the double sided tape that is on the back of the Left &
Right trim pieces.

4.

Remove 2 screws from under the fascia.

5.

Firmly place the Left & Right side trim pieces into position.

6.

Place the Top trim piece in place and use the two screws supplied to fasten the Top trim
piece.

7.

Replace upper louver.

8.

Replace the lower louver.

Lower Louver

Upper Louver

Left Side

Trim

Right Side

Trim

Bottom Trim

CAUTION:
Only Trim kit (s) supplied by the manufacture shall be used in the installation of this appliance.

Top Trim

«
...
36
37
38
39
40
...
»

Содержание Optima 70-2






















































Отзывы:

Нет отзывов