Arcflash Labs EMG-02 Скачать руководство пользователя

Страница: 9 / 17

9 |

P a g e

discharging resistor, it is important to not toggle the main switch rapidly and allow the resistor
to cool for at least 60 seconds between toggles.

2.6 Display/Firing Mode Selector/Laser Switch

The display shows the velocity of the prior shot, the battery percentage/voltage and also

shows the current and available firing modes of the gun. There are four modes: SAFE, SINGLE,
BURST, and AUTO.

To adjust the firing mode, simply press inward on the firing mode selector until the

desired firing mode is selected. NOTE: The firing mode selector button may look slightly
different on later batches of the EMG-02.

Below the firing mode selector, there is a toggle switch which activates the laser at the

front of the barrel. When toggled rearward, the laser is active. When toggled forward, the laser
is de-activated. When active the laser will illuminate continuously until toggled off.

In the SAFE mode, the gun will not fire and will display a warning should the user

depress the trigger.

Firing mode selector

Laser switch

Display

Mode selection

Battery level

Velocity

measurement

Содержание EMG-02


















Результаты поиска

Содержание EMG-02

Отзывы:

Похожие инструкции для EMG-02

Бренды по названию

Популярные бренды

Arcflash Labs EMG-02, Руководство пользователя

Результаты поиска

Содержание EMG-02

Отзывы:

Похожие инструкции для EMG-02

Бренды по названию

Популярные бренды