background image

C31/P35/P1

E-10

C31/P35/P1

E-11

E

n

g

li

s

h

Amplifier Gain Switch (P1)

This switch is to allow the gain of the P1 amplifier to be changed to suit your system requirements.

With the switch in,

 the gain is set to standard ARCAM gain of 31.5dB. This is the normal setting, 

which allows the P1 to be used in systems where there are other ARCAM power amplifiers (excluding 
the Arcam P7).

With the switch out,

 the gain is set to ‘THX standard gain’. Use this setting if your P1 is to be used in 

systems containing amplifiers with THX gain (for example, the Arcam P7).

Daisy chaining

Both the P35 and the P1 can be connected to further power amplifiers to drive more speakers (e.g., 
those in other rooms, tri-amplified speakers, etc). This technique is called ‘Daisy chaining’. 
Connect the 

AUDIO OUT

 sockets on the P35/P1 to the pre-amp. input of the next amplifier in series, left 

to left, right to right.

Remote switching

By making a connection from the 

TRIG OUT

 socket of the C31 pre-amp. to the 

REMOTE IN

 socket of 

your P35/P1, you can use the C31 to switch the power amplifier on and off. If configured in this way, 
the front panel 

POWER

 button of the C31 (or the 

POWER

 button on the remote control) switches both 

amplifiers on and off together. This facility allows you to position your power amplifier in a remote 
location (such as close to the speaker it is amplifying), yet still control it.
The connecting cable to use is a 3.5mm jack lead, wired as given on page 5. It is possible to connect 
several power amplifiers to a C31 by ‘daisy chaining’ from the 

TRIG OUT

 of one power amplifier into the 

REMOTE IN

 of the next.

Содержание C31



















Отзывы: