ARC Audio XDi 450.4 Скачать руководство пользователя страница 5

Speaker outputs

This amplifier is a multi channel amplifier design. Meaning it has more than one channel of speaker outputs. It is 
equipped with a removable plug style terminal for speaker wire connections up to 14 AWG. Make this connection 
carefully and neatly. Strip your wire back 5/16” and twist the exposed leads and insert them into the block terminal while 
being careful that there is no loose or frayed strands of wire. 
Tighten the standard head screw down on the terminal until 
the wire is tightly secured in place. If the wires ever come in 
contact with each other the amplifier will go into protection.
 

Know your total ohm load before you make any connec-
tions.

5

/

16“

8MM

Strip Speaker Wire

Ohm Loads

This amplifier operates in the traditional sense with regard to Ohm loads. Lowering the Ohm load will increase power 
output however it will also increase current draw and produce more heat. This amplifier is capable of running any mix or 
combination of Ohm load on the front and rear channels. They do not have to be the same. 

Any speaker or combination of speakers with a total combine Ohm load between 2 and 4 Ohms can be used on any single 
channel. 

Bridged loads 

must not drop below 4 ohms

 but my exceed 8 Ohms if needed. This will not damage the amplifier however 

power output will decrease at higher load. 

WARNING: This amplifier will not operate and could be 
damaged if used in the wrong configuration. At no time 
can it be operated below 2 Ohms stereo or 4 Ohms 
bridged.

INPUT

BASS

BOOST

0

9

dB

FREQ Hz

50

GAIN

MIN

HP FREQ Hz

10

1K

LP FREQ Hz

50

3K

Bass Boost

This amp has an adjustable Bass Boost that is directed to the front speakers. When laying out your system, if you plan to 
use Bass Boost (Example: Running a Bridged Subwoofer), connect those speakers to the front channels. Begin your adjust-
ments at a low volume. If you do not hear any improvement 
then the woofer does not need any boost. Use Bass Boost 
carefully. The demands on power output are tremendous. 
Try to minimize the use by changing woofer position or the 
enclosure size.

4

Top

Содержание XDi 450.4












Отзывы: