background image

Warning 

We build all ARC Audio products to play at high volumes for extended periods of 
time. Your ears however are not designed for high volume listening. This product 
can easily generate volumes that can permanently damage your hearing. We urge 
you to limit your exposure to very high volume sound. 
You may also find your state has laws governing the volume of an audio system in a 
car. Please be aware of all local and state laws in you area.  
A properly tuned and operated audio system will deliver years of enjoyment when 
used properly. 
 

Installation Instructions 

ARC Audio KAR Series Amplifiers are designed for easy installation in your vehicle. To 
ensure proper operation of your new purchase, please follow the suggestions we 
have listed below: 
 

Warning 

Please check the suitability of the installation location before you begin. Do not cut any of 
the car’s structure. Pay close attention to what is behind the panels or carpet. Often the 
manufacture will hide wires, computers or other electronic devices in the exact areas you 
wish to install in. 
 
If you do not have experience with automotive electrical and mechanical systems contact 
a professional installer. Paying a qualified installer is almost always cheaper then paying 
a dealership to repair your car. 

 

Locating the Amplifier 

The amplifiers must be securely mounted to a solid surface. Please select a dry 
location in the trunk or passenger compartment only. Do not mount the amplifier to 
any area that may have excessive vibration (like the subwoofer box). Position the 
amplifier in an area that receives sufficient airflow for proper heat dissipation. 
 

Thank you for purchasing an ARC Audio Hi-Performance Amplifier.

This ARC Audio amplifier uses a Full Range Class H architecture that significantly 
improves efficiently without compromise to the sound quality. Don’t be fooled by the 
small size. Class H amplifiers make more power for there size then traditional designs 
and offer much lower THD and higher Damping factors then Full Range Class D 
designs. 

ARC Audio...

SOLID CONSTRUCTION for SOUND Car Audio Systems. 

Setting the Gains 

So you're worried that your 8 Volt output head unit will be too much for the 
ARC Audio's 4 Volt input stage. 
 
Don't Be 
 
ARC Audio Amplifiers input stage is rated to 4 volts RMS @ 1KHz without 
clipping. 
 
Music is very dynamic. Nothing like a 1KHz test tone. It would be rare to see a 
peak as high as a test tone. Furthermore, your head unit produces its output at 
full volume but when you tune your system you always set the head unit to 
70% of maximum volume. 
 

Supplying Enough Power 
 
The Laws of Nature 

Your amplifier Does NOT make power. It converts power, or current, from your 
cars electrical system and turns it into a high power musical energy.  If the amp 
can't get all the power it needs it will not produce its full output. Your ARC 
Audio amplifier will produce Full output for longer then other amps on the 
market today. If the Voltage or Current drops too low even our amplifiers will 
drop below  their rated output. Make sure your vehicle charging system is in 
good working order. Any Hi-Performance audio amplifier will increase the 
demand on your alternator and battery. If you are unsure have your charging 
system tested by a professional technician. 
 

The Ground!!! 

Warning: Read this Carefully 
The ground wire should be connected directly to the chassis of your vehicle. 
Find a clear location close to the amplifier and remove all the paint and sound 
deadener. Use a #10 or larger screw to secure it. Never use seatbelt bolts for 
grounding. 
Remember, the ground must carry the same high current as the positive power 
wire. 
 
To reduce the risk of noise, run all signal cables away from any vehicle or power 
supply wiring. 

Running the Cables 

Carefully run the power and signal cables through the passenger compartment 
of the vehicle. Always use a rubber grommet to prevent the power wire from 
shorting and to reduce the risk of fire. A 4 gauge or larger wire should be used 
for power and ground connections. We recommend a fuse be installed on the 
power wire within 18 inches of the battery for safety. 
 

 

Содержание KS 300.2









Отзывы: