arbo HD KR Скачать руководство пользователя страница 32

Страница: 32 / 35

Troubleshooting

User Manual Chemical centrifugal pumps with mechanical seal V080716

Impeller damaged or out of
balance
Pump is in cavitation

Increase the NPSH

available

Electric motor of the
product is running
too hot

Air cooler is defect or
blocked
Cooling air inlet and outlet
is blocked

Clean the cooling air inlet and
outlet with compressed air.

Rotating parts are blocked

Clean the product.

Product is overloaded

Check the specifications of the
liquid and the product.

Safety protection
switch switches
motor off

Air cooler is defect or
blocked

Replace the air cooler or clear
the blockage.

Cooling air inlet and outlet
blocked

Clean the cooling air inlet and
outlet with compressed air.

Rotating parts are blocked

Clean the pump.

Product is overloaded

Check the specifications of the
liquid and the product.

Ambient temperature too
high
Safety protection switch is
not correctly adjusted
Motor speed is too low

Wrong frequency.

Bearings of the product are
worn or jammed

Replace the bearings.

Motor does not run on 3
phases

Flow rate too low or
no discharge
pressure

Too much resistance in the
suction and discharge line
Valves in suction and
discharge line are closed

Open the valves.

Strainer at the suction side
is clogged

Clean the strainer.

Impeller of the product is
worn

Replace the impeller.

Crystalized liquid blocks the
pump

Clean the product.

Motor speed too low

Wrong frequency.

Problem

Possible cause

Solution

Содержание HD KR




































Результаты поиска

Содержание HD KR

Отзывы:

Похожие инструкции для HD KR

Бренды по названию

Популярные бренды

arbo HD KR, Руководство пользователя

Результаты поиска

Содержание HD KR

Отзывы:

Похожие инструкции для HD KR

Бренды по названию

Популярные бренды