ARB INTENSITY SOLIS, Руководство пользователя

Страница: 2 / 4

Page 2.
SUPPLIED PARTS
1x Light body (Spot or Flood) 3x M8x30 socket head cap screws
1x Clear cover
3x M8 large washer
1x Mount bracket 3x M8 nyloc nut
1x Security torx key tool 4x M8x30 Torx drive button head screw
1x User guide. 4x M8 square nut
2x Nut cover 4x M8 spring washer
2x Replacement bezel insert 7x M8 washer
TABLE 1.
SPECIFICATION AND FEATURES
FIGURE 1.
CARE AND MAINTENANCE
• There are no user serviceable components inside the light - DO
NOT disassemble.
• Clean with warm soapy water and a sponge or soft brush. DO NOT
use solvents, scourers or hard bristle brushes. DO NOT use harsh
wash chemicals, these will remove the protective clear coat from
the lens and lens cover. Always rinse throughly.
•
Remove the clear cover periodically to clean the light lens.
•
Ensure all electrical connectors and wiring loom are secured away
from sharp edges and hot surfaces.
•
Regularly check all mounting and adjusting bolts to ensure they
are secured and tight.
• If your light requires further service or repair, return it to your local
ARB distributor.
USING THE TOUCHPAD
The digitally controlled touchpad is a unique part to the ARB
Intensity Solis driving lights and works in conjunction with the
vehicle high beam circuit and vehicle high beam dash lamp. The
touchpad will illuminate when the illumination circuit is activated
in the vehicle. To activate ARB Intensity Solis driving lights, press
the ARB logo, the ARB logo will illuminate WHITE and the lights
are then actively controlled (on/off) with the vehicle high beam
circuit. To deactivate the ARB Intensity Solis driving lights so
they will not operate with the high beam circuit, press the ARB
logo on the touchpad, the ARB logo will illuminate from WHITE to
RED indicating the system is in standby mode.
The touchpad intensity level operates by using the up and down
buttons as per Figure 2 and will change the intensity of the light
output on each press of the up/down button. The intensity bar
will illuminate in steps indicating which setting is selected. The
touchpad will remember the last known intensity setting and
revert to this setting until changed by the user.
WIRING HARNESS
ARB recommends the use of the ARB Intensity Solis Wiring
Loom (Part number : SJBHARN). This harness is designed
specifically for the ARB Intensity Solis Driving Lights and
includes the in-vehicle Touchpad for dim control.
• 36 Osram LEDs. (6 X10w & 30 X 4w)
•
Raw Lumens 18,178LM.
•
Effective Lumens 9,546LM Spot, 8,333LM Flood.
• Colour Temperature: 5700 Kelvin.
• Distance @ 1Lux – 1032m Spot, 729m Flood (Single light).
•
11° full beam width Flood.
• 6° full beam width Spot.
• Over Voltage Protection.
•
50,000+ Hour LED life span.
•
Operating Temperature -40°C to +65°C, -40°F to +149°F.
• Protected against RFI/EMC interference.
• Integrated thermal management.
•
High pressure die-cast aluminium body and mount.
• Virtually unbreakable polycarbonate lens.
• UV stable moulded polycarbonate lens cover.
•
Multiple position mount.
• Durable UV stable powder coat.
• Pressure equalisation breather.
•
Dust and waterproof to IP68.
•
High power Amphenol AT06 waterproof connector.
• Tested to MIL810-STDG for vibration.
•
RoHS compliant.
•
Input voltage 10-30V DC.
• Power draw 165W.
• Current draw 12.4 Amps @ 13.2V.
TOUCHPAD
FIGURE 2
The above image shows the touchpad with 25%
intensity setting selected.
5%
50%
100%