AR 10044778 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 54

AR 10044778 Скачать руководство пользователя страница 40

Model 100U1000

22

Rev B

2.4.7

Interlocks

The 4U MPC has one interlock circuit that is wired to the rear panel Safety Interlock connector. This

interlock requires a normally closed external circuit to allow the unit to function.

2.4.7.1

Inhibit Interlock

This interlock circuit inhibits RF amplification by disabling the low level (A1) and Power (A2 & A3)

amplifier stages.

The Inhibit Interlock is wired to the rear panel interlock connector pins 1 and 8. A closed circuit from

interlock connector pin 1 to pin 8 is required for normal operation. Opening the Inhibit Interlock connection

will inhibit the amplifier and display

Fault:Interlock

on the front panel Touch Display.

When the Inhibit Interlock circuit is restored to a closed condition, the Inhibit Interlock fault can be cleared

by pressing the

RESET

button on the front panel LCD or by using the remote reset command (when the

Toggle Switch is set to

REMOTE

).

«
...
38
39
40
41
42
...
»

Содержание 10044778























































Отзывы:

Нет отзывов