Barrel Buddie
™
Installation, Operation & Maintenance Guide
Model# 270669
LIMITED WARRANTY
Lifetime Products LLC warrants that this Barrel Buddie
shall be free from defective components due to defects
in materials or workmanship for a period of one (1) year
from the date of purchase. If a defect is shown, Lifetime
Products LLC will, at Lifetime Product’s sole discretion,
either repair or replace the product without charge. No
cash refunds will be made. This warranty is provided
solely to the original consumer purchaser of the product
and may not be transferred or assigned. If Lifetime
Products chooses to replace the equipment, Lifetime
Products may replace it with reconditioned equipment.
Parts used in repairing or replacing the equipment will
be warranted for 90 days from the date the equipment is
returned to you or the remainder of the original warranty
period, whichever is longer.
This warranty does not apply to damage resulting from
accident, misuse, abuse, lack of reasonable care, failure
to follow safety and installation instructions.
This warranty will be void if defects occur due to failure
to observe the following conditions:
• Water flowing through the unit is free of
particulate matter.
• Water flowing through the unit is below
40°F or above 100°F.
• Water pressure is more than 80 PSI.
• Do not use outdoors or in a location that is subjected
to direct sunlight or freezing.
This warranty will not be effective unless and until
the Aquatic Life product is shown to have been used
in accordance with the installation and maintenance
instructions accompanying the product.
THIS CONSTITUTES LIFETIME PRODUCTS ENTIRE
WARRANTY AND LIFETIME PRODUCTS MAKES NO
OTHER WARRANTIES, WHETHER EXPRESS OR
IMPLIED, WITH RESPECT TO THE PRODUCT. LIFETIME
PRODUCTS, LLC SPECIFICALLY DISCLAIMS ANY AND
ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. IF LIFETIME
PRODUCTS, LLC CANNOT LAWFULLY DISCLAIM IMPLIED
WARRANTIES UNDER THIS LIMITED WARRANTY, ALL
SUCH WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED IN DURATION TO THE DURATION
OF THIS WARRANTY. LIFETIME PRODUCTS IS NOT
RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM ANY
BREACH OF WARRANTY OR CONDITION, OR UNDER
ANY OTHER LEGAL THEORY. LIFETIME PRODUCTS, LLC
EXPRESSLY DISCLAIMS ALL ALLEGED DAMAGES FOR LOSS
OF MARINE LIFE, PERSONAL INJURY, AND/OR PROPERTY
DAMAGE.
Some states and provinces do not allow the exclusion
or limitation of incidental or consequential damages
or exclusions or limitations on the duration of implied
warranties or conditions, so the above limitations or
exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights
that vary by state or province.
Lifetime Products, LLC shall not have any obligations
under this warranty unless the owner notifies Lifetime
Products, LLC in writing of any alleged defect(s) within 30
days of discovery of the defect(s).
Any notice to Lifetime Products, LLC must be delivered by
United States or electronic mail to the following address:
U.S. Mail: Lifetime Products, LLC, 9710 Klingerman St., S.
El Monte, CA 91733 or electronic mail: customersupport@
aquaticlife.com. Lifetime Products shall be allowed a
reasonable period of time to investigate any warranty
claim and to perform any testing Lifetime Products
deems necessary to determine the cause of the defect.
This warranty shall be interpreted under the laws of the
State of California.
Lifetime Products, LLC
9710 Klingerman St. | S. El Monte, CA 91733
[email protected]
www.aquaticlife.com
UNIT MAINTENANCE
Monthly, or as needed, remove the sensors
and wipe with a clean, damp cloth.
Do not use abrasive cleaners on the
sensors. If calcium or minerals build-up
on the sensors, soak in a 50/50 solution of
vinegar and water then wipe clean.
TROUBLESHOOTING
The solenoid does not open when water is
below the low sensor.
➊
Ensure the unit is powered on and the red
LED light is illuminated on the controller.
➋
Ensure the sensor cord is completely
plugged into the jack on the controller
The solenoid does not close when water
reaches the high sensor.
➊
Ensure the unit is powered on and the red
LED light is illuminated on the controller.
➋
Ensure the sensor cord is completely
plugged into the jack on the controller.
➌
Check for debris trapped in the solenoid.
Water should be pre-filtered prior to
flowing through the solenoid.