6
☎
US (866) 877-6637 |
☎
CAN (866) 766-3426 | aquascapeinc.com
IonGen Probe Maintenance
• The replaceable IonGen
Probe will typically last one
or more seasons, depending
on the usage, quantity of
water and water chemistry
of the water feature (Ex. 14).
The IonGen System Control
Panel display will read "00"
when the IonGen Probe is
completely exhausted or
there is a fault in the operation of the system.
General Maintenance
NOTE:
It is not unusual to have low, or even no copper
level readings on the test kit, no matter how high the
IonGen System's ionization level setting. This is due to
the copper being used within the water feature. Periodic
copper testing will ensure that the levels are below the
maximum level of .0.25 ppm.
Operating the IonGen System on an existing water
feature with algae present
• Set the IonGen System
to the highest ionization
level possible if there are
significant levels of algae
present in the water feature.
In some water feature
applications you may find
that you are not able to raise
the ionization level to the
higher power setting (levels
7 - 10) (Ex. 13). This is typically due to the water chemistry
of the water feature on the water flow rate across the
IonGen Probe. In most cases, the IonGen System will
still produce sufficient quantity of ions to kill the algae. Be
patient, as it may take several days to a few weeks for
noticeable results to occur. Using the included copper
test kit, test the water over a period of days to ensure that
the copper levels
DO NOT
rise above .0.25 ppm. The
ionization level can be lowered once the algae levels have
decreased or the copper test kit indicates a maximum
level of .0.25 ppm.
• Pre-existing algae levels, poor water conditions, as well as
the volume of water in the water feature are all factors that
affect the speed at which the IonGen System will achieve
desired results.
• If the level of copper rises above .0.25 ppm, reduce the
IonGen System down to level one or unplug the IonGen
System until the copper levels fall below .0.25 ppm. A
water change can also be conducted if the copper levels
are significantly above .0.25 ppm.
• In the case of a power failure, the IonGen System Control
Panel's internal memory will reset itself to the last setting
before the power failure.
• It is recommended to visually inspect the bars on the
IonGen Probe from time to time, and replace the IonGen
Probe if the bars are significantly worn.
• The Aquascape IonGen System does contain a built-in,
self-cleaning mechanism that reduces the build-up of
oxidation scale on the bars, but requires sufficient water
flow to work properly. An excessive build-up of scale on
the bars is an indicator that there may not be sufficient
water flow. Significant oxidation scale on the bars will
decrease the distribution of ions being released into the
water, as well as affect the ability to raise and lower the
Control Panel's ionization level. Scale build-up can easily
be brushed or scraped off the bars, immediately improving
IonGen Probe performance. If you notice repeated scale
build-up, you may want to move the IonGen Probe to a
location with higher water flow, such as plumbing it directly
into the main recirculating system.
• Starting out each year with a new IonGen Probe is
recommended and will significantly boost the performance
of the IonGen System.
Winter Application
• It is recommended to shut down the IonGen
™
System
in regions that have climates that experience cold
temperatures. This will prevent elevated copper levels
during the time of the year when there is no algae growth,
and will prolong the life of the IonGen Probe.
• The IonGen System's Control Panel is weather resistant,
but steps to protect it from the elements, such as
mounting the panel above the ground, are recommended
to maximize its lifespan.
• The Flow Chamber, when plumbed directly into the
recirculating system, needs to be located in a region that
will drain for servicing the replacement IonGen Probe, as
well as allowing the Flow Chamber fitting to over-winter.
• If shutting down the water feature during the winter, make
sure the plumbing line is drained free of water. Failure to
do so may cause water remaining in the plumbing line to
freeze, potentially cracking the Flow Chamber and voiding
the warranty.
• Prior to restarting the IonGen System in the spring, it is
a good idea to remove and inspect the IonGen Probe
to ensure it is free of debris and scale build-up, and not
exhausted or worn. Scrape away any scale build-up from
the IonGen Probe's bars. Replace worn IonGen Probes.
See section above the IonGen Probe maintenance for
more information.
Ex. 14
Ex. 13