Assembly
1) Locate a flat, dry area with access to electrical outlet or extension cord.
IMPORTANT
: Because of the size and weight of the Supertramp™ 27, careful
thought must be given to the setup area. Ideally, the tube should be carried into
position while inside it’s protective storage bag. The best setup position will also
make launching easy. Therefore, locate the Supertramp™ near the water’s edge.
NOTE
: Dragging or sliding the Supertramp™ over ground either before or after
inflation can cause damage.
2) Once in the setup/ launch position, unfold the Supertramp™ tube completely
and locate the Main Valve. The Main Valve is located near the warning labels
near one of the corners.
3) Using a high output pump, place the inflation hose with proper adaptor into
the Main Valve to inflate the Supertramp
™ tube.
Inflate to 0.8 psi (0,055 bar).
Check for proper air pressure using a manometer. After inflation, replace Main
Valve cover. Inflation times can vary by inflator, but the main section should be
firm and tight when completely inflated.
DO NOT OVER-FILL
. Excessively
high pressure can cause damage to the product and may void the warranty.
Carefully monitor air pressure in the product especially during hot weather.
WARNING:
Do not use an air compressor to inflate tube. Air compressors are
designed for high pressure inflation and can cause tube to burst if over-inflated.
4)
IMPORTANT
: Once the tube is inflated, locate the Anchor Bridle and lay out
1 anchor bridle webbing strap at
EVERY CORNER
(marked in
Fig.1
as item
A-D
). As you assemble frame pieces in the following instruction, you will slide
the anchor bridle onto the frame at these locations.
5) Locate the (12) steel frame pieces, protective sleeves and fastening
hardware. Slide the protective sleeves over each bar before assembling as
shown in
Fig. 2
. Use the straps to hold the frame in place as shown in
Fig 3
.
Slide each bar into the bar holders and connect the frame bars at the point of
each corner as shown in
Fig. 4.
Do this by sliding the smaller end of bar into
the larger end and secure with fastener set using the included Allen wrench.
NOTE
: Make sure the spring slots are facing
UPWARD
and the protective
sleeves are on each bar before bolting them together.
NOTE
: For long-term use, seal fastener bolt threads with LocTite™ or similar
Anti-seize lubricant.
North Sports, Inc. #1 North Shore Dr, SE White Salmon, WA 98672 TEL: (509) 493-4938 FAX: (509) 493-4966
6) IMPORTANT:
Make sure to incorporate anchor bridle into frame as frame is
assembled. Pull the anchor bridle webbing through the bridle loop to make
a ‘cinch loop’ as shown in
Fig. 5a - 5b
. As frame is assembled, slide the
anchor bridle onto the frame at each corner as shown in
Fig.6
.
8) Next, install the jump mats using trampoline springs. This is a job best done
with at least two partners working exactly opposite each other. Once the mat is
correctly aligned with the trampoline, install 4 springs at each corner as shown in
Figure 7 - Springs.
Working inward from the corners, continue installing 2 more
springs on each corner until all springs have been installed.
USE SPRING HOOK (provided) AND/OR GLOVES TO PROTECT YOUR
HANDS FROM PINCHING DURING ASSEMBLY.
9) Finally, properly position the Spring Pad Covers with webbing straps facing
downward. Reach underneath the spring pad cover to connect each webbing
strap around the springs. Secure each strap with buckle to ensure a snug fit.
10) To launch the product, make sure to have at least 4 people evenly spaced
around the product to help carry it.
NEVER DRAG THE SUPERTRAMP
™
! YOU
MUST LIFT AND SET TO AVOID ANY ACCIDENTAL TEARING AND/OR
ABRASION.
www.Aquaglide.com
Spring Slots
(should face upward)
27
A
B
C
D
Figure 2
sleeve at each corner
use straps to secure frame
Spring holes
face UP
sleeve slides
up to cover
frame bolt
Figure 3
Figure 4
Figure 1
