TOWABLE |
OWNER’S MANUAL
aquaglide.com | © 2016 Aquaglide
riders. Such an addition can break or stretch which may lead to injury
of users or boat occupants.
• Rope is subject to deterioration when exposed to direct sunlight.
The life of the product will be extended when stored away from
sunlight.
• The tow rope should be replaced when signs of deterioration
appear, indicated by the existence of discoloration, wearing, fraying or
unraveling.
• Do not add hardware or attachments that are not supplied by the
manufacturer.
Wakeboard Towers and Tow Points
Wakeboard towers are not designed for pulling towables. Use
only lifting eyes for towing tubes with 2 or more riders. Do not tow
inflatables from ski pylons or ski eyes unless recommended by the
boat manufacturer. Tow pylons and ski eyes installed aftermarket are
not intended for towing inflatables. Aquaglide
® assumes no liability for
injuries or damages resulting from not following these instructions.
Proper Inflation
Proper inflation is the key to optimum performance and durability of this
product. During use, the cover should be taught with few wrinkles, and
you should barely sink into the tube when standing on it. If the tube
is under inflated, damage can occur to the tube when towing. Use
caution and do not over-inflate above 1.4 psi. When not in use, be
sure to remove some air from the tube and move the tube to a shaded
location. Exposure to direct sunlight heats the tube and causes the air
inside to expand, causing serious damage to the seams and I-beams.
Rapid Inflate Valve Inflating – Unscrew the cap and insert the pump
fitting into the valve. Be sure to open the flap at the base of the valve.
Remove the pump fitting after filling completely, and make sure the
black flap is seated securely closing the valve. If the flap is not seated,
pull red tab to close valve. Replace the cap.
Deflating – Unscrew the cap and use a dull object to hold the flap open
while the product deflates. Replace the cap for storage.
Assembly Instructions
1. Lay the product out on a flat surface without sharp objects that
could puncture the PVC bladder or cover. If the product has an outer
cover, make sure the inside PVC bladder is unfolded and the valves are
in the correct position, aligned with the cover valve openings.
2. Inflate the product to about 50% full. If your product has a cover,
re-check to make sure it is correctly aligned with the PVC bladder and
valves. If there is more than one chamber in the bladder, inflate the
outer chamber first. After the cover is aligned with the PVC bladder,
inflate the chambers to 100% starting with the outer chamber.
DO NOT DRAG the product into the water. Carry the product to avoid
wear on the cover and possible punctures of the PVC bladder. To
anchor the product, always use the quick release towing attachment.
For longer term anchoring, run the anchor line from the towing
attachment through the fitting in the center of the bottom of the tube to
anchor the tube in the middle.
Maintaining and Monitoring Proper Inflation
It is important to monitor the amount of air in your Aquaglide
® product
as heat will cause the bladder to expand, possibly damaging seams
or I-beams. If you leave a full tube sitting in the sun for any length of
time it will expand. Either store it in the shade or let some air out.
Don’t leave your product on the beach, dock or boat full of air! If the
product is stored out of the sun in a cool place, you may need to add
some air. Check and adjust the inflation level each time you use your
product for maximum performance and enjoyment.
Towing Attachment
Use a tow rope of at least 1500 lbs. average tensile strength for pull
-
ing a single person, 2375 lbs. average tensile strength for pulling two
people, 3350 lbs. average tensile strength for pulling three people,
and 4100 lbs. average tensile strength for pulling four people on an
inflatable tube. The tow rope should be at least 50 feet in length, but
not exceed 65 feet.
Attach your towable to the tow rope using the quick connect
attachment. Note: The Airport Classic does not come with a quick
connect.
Storage
When taking the product out of the water, pull it out using the front
towing strap so the water is able to drain out of the mesh drains in
the bottom back. Allow the towable to dry completely to prevent
mildew. If using in salt water, rinse the product with fresh water and
allow to dry completely before storing. Release all of the air from
the chamber(s) and fold the towable. It is best to store the product
inside a warm area during cold weather. Do not expose to freezing
temperatures, as it can damage the material and cause cracks in the
PVC bladder.