INSTALLATION GUIDE
1. Dig a hole 62,5 cm long x 32,5 cm wide x 30 cm deep.
Fig. 1
2. Dig a narrow trench for the tubing (approximately 25 cm
long x 5 cm wide x 7,5 cm deep). Fig. 2
3. Place the reservoir inside the hole, make sure it is level.
Fig. 3
4. Connect the tubing to the pump. Fig. 4
5. Place the pump inside the reservoir, route the hose and
power cord through the notch in the reservoir. Fig. 5
6. Assemble the check valve, inlet and gasket. Make sure
that the inlet adapter is pointed in the same direction as
the spillway. If not, carefully turn the adapter. Fig. 6
7. Connect hose to the inlet on the bottom of the fountain.
Fig.7
8. Place the waterfall basin on the ground behind the reser-
voir. Position the waterfall so that the spillway is directly
above the middle of the reservoir. Check to make sure
the waterfall is level, front to back as well as left to right.
Fig. 8
9. Fill the reservoir and waterfall basin with water then
install the lid. Fig. 9
10. Connect the pump to a earthed wall socket. Check for
leaks, then fill in the hole with soil. Now decorate with
rocks and plants as desired. Fig. 10
INSTRUCTIONS DE BRANCHEMENT
1. Dig a hole 62,5 cm long x 32,5 cm wide x 30 cm deep.
Fig. 1
2. Dig a narrow trench for the tubing (approximately 25 cm
long x 5 cm wide x 7,5 cm deep). Fig. 2
3. Place the reservoir inside the hole, make sure it is level.
Fig. 3
4. Connect the tubing to the pump. Fig. 4
5. Place the pump inside the reservoir, route the hose and
power cord through the notch in the reservoir. Fig. 5
6. Assemble the check valve, inlet and gasket. Make sure
that the inlet adapter is pointed in the same direction as
the spillway. If not, carefully turn the adapter. Fig. 6
7. Connect hose to the inlet on the bottom of the fountain.
Fig.7
8. Place the waterfall basin on the ground behind the reser-
voir. Position the waterfall so that the spillway is directly
above the middle of the reservoir. Check to make sure
the waterfall is level, front to back as well as left to right.
Fig. 8
9. Fill the reservoir and waterfall basin with water then
install the lid. Fig. 9
10. Connect the pump to a earthed wall socket. Check for
leaks, then fill in the hole with soil. Now decorate with
rocks and plants as desired. Fig. 10
ANSCHLUSSANWEISUNG
1. Dig a hole 62,5 cm long x 32,5 cm wide x 30 cm deep.
Fig. 1
2. Dig a narrow trench for the tubing (approximately 25 cm
long x 5 cm wide x 7,5 cm deep). Fig. 2
3. Place the reservoir inside the hole, make sure it is level.
Fig. 3
4. Connect the tubing to the pump. Fig. 4
5. Place the pump inside the reservoir, route the hose and
power cord through the notch in the reservoir. Fig. 5
6. Assemble the check valve, inlet and gasket. Make sure
that the inlet adapter is pointed in the same direction as
the spillway. If not, carefully turn the adapter. Fig. 6
7. Connect hose to the inlet on the bottom of the fountain.
Fig.7
8. Place the waterfall basin on the ground behind the reser-
voir. Position the waterfall so that the spillway is directly
above the middle of the reservoir. Check to make sure
the waterfall is level, front to back as well as left to right.
Fig. 8
9. Fill the reservoir and waterfall basin with water then
install the lid. Fig. 9
10. Connect the pump to a earthed wall socket. Check for
leaks, then fill in the hole with soil. Now decorate with
rocks and plants as desired. Fig. 10
AANSLUITINSTRUCTIES
1. Graaf een gat 62,5 cm lang x 32,5 cm breed x 30 cm
diep. Fig . 1
2. Graaf een smalle geul voor de slang en kabel ( ongeveer
25 cm lang x 5 cm breed x 7,5 cm diep ). Fig . 2
3. Plaats het reservoir in het gat, zorg ervoor dat deze
waterpas staat. Fig . 3
4. Sluit de slang aan op de pomp. Fig . 4
5. Plaats de pomp in het reservoir, leid de slang en pomp-
snoer door de uitsparing in het reservoir. Fig . 5
6. Monteer de terugslagklep , inlaat en de O ring, zorg
ervoor dat slangtule in dezelfde richting wijst als de
overloop zo niet voorzichtig draaien. Fig . 6
7. Sluit de slang aan op de inlaat aan de onderkant van de
watervalbak. fig. 7
8. Plaats de watervalbak op de grond achter het reservoir.
Positioneer de bak met de overloop boven het midden
van het waterreservoir. Zorg ervoor dat de watervalbak
geheel waterpas staat. Fig . 8
9. Vul het reservoir en de watervalbak met water en
installeer vervolgens de deksel. Fig . 9
10. Sluit de pomp aan op een geaard stopcontact, controleer
op lekkage, vul nu het gat op met grond. Nu kunt u de
mini waterval aankleden met planten en stenen geheel
naar uw wens. Fig . 10
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10