background image

19

19

Order #

Item

HCAB6704

Rubber Drain Plug

HCAB9042

Recovery Pads

HCAB6700

Waterproof Switch Boot w/ON-OFF Plate

HCAB8602

Assembled 3-channel Radio Box

HCAB6701

Radio Box Water Seal Boot (2)

HCAB7008

Pushbutton Cowl Locks (2)

HCAB7102

TS2 Display/Set-up Stand

HCAB6218

Cowl Body Clip w/washer (2)

HCAB8604

Antenna Tube w/cap 

Order #

Item

HCAB6703

Antenna/Cable Seal Boot (2)

HCAB6702

Receiver Waterproof Balloon (2)

HCAB8603

Radio Box Foam

HCAB6217

Fiberglass Cowl (White)

HCAB6313

Decal Set (All)

HCAB7802

L-Link Pushrod Connector (2)

HCAB8606

Radio Box Waterproof Tape

HCAB3000

Speed Grease Driveline Cable Lube

GPMQ4103

8oz. Fuel Tank

To order replacement parts for the AquaCraft Top Speed 2, use the order numbers in the Replacement Parts List that follows.
Replacement parts are available only as listed and can be purchased from hobby shops or mail order/ Internet order firms.
Hardware items (screws, nuts, bolts) are also available from these outlets. If you need assistance locating a dealer to purchase
parts, visit 

www.aquacraftmodels.com and click on “Where to Buy.” If this kit is missing parts, contact Hobbico Product Support.

Replacement Parts List

ORDERING REPLACEMENT PARTS

ENGINE TEMPLATES

Template #1

Template #2

Содержание Top Speed 2 HCAB5010





















Отзывы: