background image

PREPARING THE POOL WATER

 

Salt Addition Chart 

The following salt chart is included for reference only.  Once your Pool Pilot Digital is properly programmed to the pool water 
volume, it will automatically indicate how much salt is needed.  To use this chart: 

1.

 

Find your current salt level (ppm or g/l) in the left column.  (This can be obtained from your Pool Pilot display or by 
testing your water.) 

2.

 

Find your pool/spa volume in the second row (Gallons or Liters). 

3.

 

Find the amount of salt needed to bring your pool to the ideal level by finding the intersection of the row and column.  

For volumes other than what is shown, use combinations of various columns.   
For example, for an 11,000 gallon (41,646 liter) pool with a salt level of 500 ppm (5 mg/l), the column value for 1000 gallons 
(4,000 liters) (21 pounds (9 kg)) is added to the column value for 10,000 gallons (38,000 liters) (209 pounds (95 kg)) which gives 
a total of 230 pounds (104 kg) of salt needed to bring your pool salt level up to the ideal level of 3000 ppm (3.0 g/l). 

 

Pounds (kilograms) of Salt needed to attain 3000 ppm (3.0 g/l) 

Pool/Spa Volume in Gallons (Liters) 

1,000  2,000  5,000  10,000 15,000 20,000 25,000 30,000 35,000 40,000 

Current 
salt level  
ppm 

(g/l)

 

(4,000)  (8,000)  (18,000) (38,000) (56,000) (76,000) (94,000) (114,000) 

(132,000) 

(152,000)

25  50  125 250 376 501 626 751 876 1,002 

(11)  (23)  (57)  (114) (170) (227) (284) (341) (398) (454) 

23 

46 

115 

230 

344 

459 

574 

689 

803 

918 

250  

(0.25) 

(10) 

(21) 

(52) 

(104) 

(156) 

(208) 

(260) 

(312) 

(364) 

(416) 

21  42  104 209 313 417 522 626 730 835 

500  

(0.50) 

(9)  (19)  (47)  (95)  (142) (189) (237) (284) (331) (379) 

19 

38 

94 

188 

282 

376 

470 

563 

657 

751 

750  

(0.75) 

(9) 

(17) 

(43) 

(85) 

(128) 

(170) 

(213) 

(256) 

(298) 

(341) 

17  33  83  167 250 334 417 501 584 668 

1,000  

(1.0) 

(8)  (15)  (38)  (76)  (114) (151) (189) (227) (265) (303) 

15 

29 

73 

146 

219 

292 

365 

438 

511 

584 

1,250  

(1.25) 

(7) 

(13) 

(33) 

(66) 

(99) 

(133) 

(166) 

(199) 

(232) 

(265) 

13  25  63  125 188 250 313 376 438 501 

1,500 

(1.5) 

(6)  (11)  (28)  (57)  (85)  (114) (142) (170) (199) (227) 

10 

21 

52 

104 

157 

209 

261 

313 

365 

417 

1,750 

(1.75) 

(5) 

(9) 

(24) 

(47) 

(71) 

(95) 

(118) 

(142) 

(166) 

(189) 

8  17  42  83  125 167 209 250 292 334 

2,000 

(2.0) 

(4)  (8)  (19) (38) (57) (76) (95) (114) (133) (151) 

13 

31 

63 

94 

125 

157 

188 

219 

250 

2,250 

(2.25) 

(3) 

(6) 

(14) 

(28) 

(43) 

(57) 

(71) 

(85) 

(99) 

(114) 

4  8  21 42 63 83 104 125 146 167 

2,500 

(2.5) 

(2)  (4)  (9)  (19) (28) (38) (47) (57) (66) (76) 

3,000 

(3.0) 

Ideal 

3,500 

(3.5) 

OK for Pool Pilot Operation – (This is typically the maximum salt level desired by most pool 

owners/operators since most people can taste salt levels above this.) 

Greater 

than  

3,500 

OK for Pool Pilot Operation but greater than 6000 ppm can cause corrosion to metallic 

objects- (If lower salt level is desired, partially drain and refill with fresh water.) 

 

Содержание Pool Pilot 75003
























































Отзывы: