background image

 

User Manual Thermal X - R Series Chillers   

 

 

 

 

 

Page 28 

Recommended Preventative Maintenance Program 

A comprehensive preventative maintenance section is included in the back of this manual 

Operation 

Frequency 

Refrigerant Charge 

6 Monthly 

Electrical connections are tight 

6 Monthly 

Compressor amp draw 

12 Monthly 

Pump amp draw 

12 Monthly 

Condenser strainer cleaned 

6 Monthly 

WARRANTY 

Any claim under this warranty must be made within the discussed time period of the date of purchase 

of the product. To make a claim under the warranty, return the product (with proof of purchase) to 

the supplier where you purchased the product or contact Aqua Cooler regarding warranty conditions.   

Aqua Cooler

 

will pay  your reasonable, direct  expenses of claiming under this warranty.  You may 

submit  details  and  proof  of  your  expense  claim  to  Aqua  Cooler  Pty  Ltd  for  consideration.  This 

warranty is given by Aqua Cooler Pty Ltd, U14, 2-12 Knobel Court Shailer Park 4128 QLD.

 

This warranty is provided in addition to other rights and remedies you have under law: Our goods 

come with guarantees which cannot be excluded under Australian Consumer Law. You are entitled 

to replacement or refund for a major failure and to compensation for other reasonably foreseeable 

loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of 

acceptable quality and the failure does not amount to a major failure.  

A comprehensive commissioning procedure is attached in the end of the manual. This must be carried 

out in accordance with the procedure and returned to Aqua Cooler a[email protected]

Aqua  Cooler  offers  a  commissioning  program  and  can  arrange  this  for  you.  Failing  to  follow  the 

commissioning procedure may void this warranty.  

GENERAL APPLICATION 

The chiller is designed to refrigerate and circulate water to a heat developing process to aid in keeping 

that  process  cool.  They  are  supplied  with  an  immersed  coiled  copper  evaporator,  or  plate  heat 

exchanger,  or  shell&tube  evaporator  (model  dependant)  an  air  cooled  condenser  and  a  scroll 

compressor to circulate the refrigerant gas. Water is circulated out of the unit via a pump. The chiller 

is design to be installed outdoors and refrigerate water for a heat developing process – not for drinking 

or food preparation purposes. Any other use of this water chiller is a not as it is intended.  

 

 

 

Содержание Thermal X R Series





































Отзывы: