background image

AP-DWS1000 Drinking Water Appliance Owner’s Manual

Installation Precautions

6888931 0701

Installation and 
Operating Instructions

Do not use with water that is microbiologically 
unsafe or of unknown quality without adequate 
disinfection before or after the system.

Installation must comply with state and local 
plumbing codes.

Systems certified for cyst reduction may be 
used on disinfected water that may contain 
filterable cysts.

System must be protected from freezing.  Drain 
filter when room temperature drops below 
40°F (4.4°C).

Do not install on line pressure above 125 psi 
(862 kPa).

Do not install on hot water line. Maximum 
temperature allowed is 100°F (38°C).

The filter must be installed with the inlet and 
outlet ports as labeled. Make sure not to 
reverse connections.

Do not use wicking or sealer for fitting connections 
into head of filter. Use Teflon

®

tape for connections.

Do not use torch or other high temperature 
sources near filter or plastic cartridge.

Do not install near electric wires or water pipes 
which will be in the path of drill when selecting 
the position to mount bracket.

Do not install in direct sunlight.

Allow a minimum of 2” (5cm) clear space 
under filter to facilitate cartridge change.

Mount filter in such a position as to prevent it 
from being struck by other items.

Teflon is a registered trademark of E.I. DuPont.

Содержание AP-DWS1000 LF












Отзывы: